Aiwa TV Repair: Common Faults and Solutions.
Search: Aiwa
Results: 309
Results: 309
Aiwa Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
AIWA | NSX-SZ510 | Red LED doesn't turn on | Altered q-130 | samuel leite | |
SOM AIWA | CX-ZM2800HR | Does not turn on, display is off. | Fusistor in position r998 and r999 open, and damaged audio output stk-419-130 | Audio output, and fuses r998 and r999. | MARCONES DE ARARIPINA-PE |
AIWA | CX-NS303LH | When you press the power key, it turns on and quickly returns to the demo screen. | Power push-button key with internal recess. | The ideal would be to replace it, but I didn't have one, so I decided to open it and sand the dirt with tweezers. (tec.edfesom varjota-ce) | Edfesom |
AIWA | NSX-S70, NSX-A74, NSX-S90, NSX-S74, NSX-F9, NSX-F12, NSX-F15, Z-R710, Z-R800, Z-R900 | Disarms when turning on the on/off button | Check protection circuit. excess current detector (q213 and q214). dc detector in the intermediate stage (q106 and q107). ac voltage failure detector (q108 and q109). | Eduardo Marques | |
AIWA | NSX-S70, NSX-A74, NSX-S90, NSX-S74, NSX-F9, NSX-F12, NSX-F15, Z-R710, Z-R800, Z-R900 | Disarms when turning on the on/off button | Check resistors r287 and r288 (SMD 39ω) and r215, r216, r291, r292 (SMD 100ω) | Eduardo Marques | |
AIWA | NSX-S70, NSX-A74, NSX-S90, NSX-S74, NSX-F9, NSX-F12, NSX-F15, Z-R710, Z-R800, Z-R900 | Disarms when turning on the on/off button | Check that the protection terminal has a voltage of 4 volts | Eduardo Marques | |
AIWA | NSX-S70, NSX-A74, NSX-S90, NSX-S74, NSX-F9, NSX-F12, NSX-F15, Z-R710, Z-R800, Z-R900 | Disarms when turning on the on/off button | Check that transistors q101 and q102 have 12 volts on the side plate (standby voltage) | Eduardo Marques | |
AIWA | NSX-S70, NSX-A74, NSX-S90, NSX-S74, NSX-F9, NSX-F12, NSX-F15, Z-R710, Z-R800, Z-R900 | Output burnt out or device does not turn on. | Check the output transistors (they are shorted), check the polarization diodes and the 0.15 ω/2watt resistors connected to the emitters | Eduardo Marques | |
AIWA | NSX-S70, NSX-A74, NSX-S90, NSX-S74, NSX-F9, NSX-F12, NSX-F15, Z-R710, Z-R800, Z-R900 | Output burnt out or device does not turn on. | Check fets q219 and q220 (2sk2723) can be replaced by buk444-500 | Eduardo Marques | |
AIWA | NSX-S70, NSX-A74, NSX-S90, NSX-S74, NSX-F9, NSX-F12, NSX-F15, Z-R710, Z-R800, Z-R900 | Output burnt out or device does not turn on. | Check pr201, pr 202 (side plate resistors) | Eduardo Marques | |
AIWA | NSX-S70, NSX-A74, NSX-S90, NSX-S74, NSX-F9, NSX-F12, NSX-F15, Z-R710, Z-R800, Z-R900 | Output burnt out or device does not turn on. | Check pr001, pr002, pr005 and pr006 (transformer board fuses) | Eduardo Marques | |
AIWA | CX-NF15LH | When turning on the LEDs on the CD's optical drive and the dek's forward indication flashes < < > > they light up but nothing works | Defective components | ? | Raimundo |
AIWA | TODOS | No sound even with the outputs ok | Headphone jack | Clean with contact cleaner | Genilson |
AIWA | NSX-F9 | FM with very low level | Tuning coil next to ic770 (la1837) | Roger Rodrigues | |
AIWA | CX-NSZ50LH | Does not leave stand bay | Crystal behind the display or transistor behind the display, just change and finish | eletronica publisom rgn tec jorge alves | |
AIWA | NSX-S229 | Hoarse sound and does not arm the relay | Transistor q112 open | multsom | |
AIWA | NSX-F969 | It turns on the panel and turns it off, and sometimes it doesn't even light the panel. | Check q224 fet 2sk 2937 which may be faulty. | I replaced it and it stopped turning off and it worked normally, good luck to everyone, | Eronaldo (erontec) |
AIWA | NSX-F969 | It turns on but the tuning doesn't stop, just press the tuning to stop. | Adjust coil l771 | When adjusting, the tuning was normal, good luck, (erontec). | Eronaldo (erontec) |
AIWA | NSX | Didn't care | With a screwdriver short the q115 terminal 3 between base and collector | Went back to work | gustavo |
AIWA | NSX F959 | No high-pitched sound (high output) | Q102 (can be jumpered - tsound is already a place on the board next to a jumper/resistor) and q103 (can be left without) | Baguatech |