MITSUBISHI TV Repair: Common Faults and Solutions.
Search: MITSUBISHI
Results: 1346
Results: 1346
MITSUBISHI Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| MITSUBISHI | TC2010 | Bad sound on the channels. like it's out of tune. in av normal sound. anomaly in the sound only in the channels. | Capacitor c304 de 1mf/50v. | If you pick it up, the sound improves. By changing it, it solved the problem. | Romildo Behrend |
| MITSUBISHI | TC2099 | Burning horizontal output transistor | Grounding track of the t551 driver transformer broken. | The track on the aluminum cooler terminal on the edge of the board was redone. tv ok. | Denys de Sene |
| MITSUBISHI | TC 2018-PS | TV arrived stopped, the owner already said that it was turning off quickly and went into protection, it remained in stanby | 33 v9lts diode shorted d 102 | <small>This email address is being protected from spambots. You need JavaScript enabled to view it.</small> | |
| MITSUBISHI | TC 2099 | Does not turn on, LED is off. voltage across the power supply capacitor | Str s6707 shorted | Replaced and the TV works. | Carlão |
| MITSUBISHI | TC1498 | Light comes on on the panel, does not go out of stand-by, when pressing the power button nothing happens, power supply b+ with 37 volts. | In this case I removed the pacifier from the tube and the fly-back oscillated, some clear sparks appeared inside the tube barrel indicating a short in the tube! | The tube that was shorted was replaced, but the image still didn't appear, leaving those bands on the screen, that is, out of horizontal frequency, just changing the c208 1μF x 100v and the TV started working normally again! | Fernando Alcantra |
| MITSUBISHI | TC2018PS | Channel locked asking for password | Lost password | Enter the menu in the place that asks for the password, you don't know it, press the q/v key on the control 4 times to unlock all channels | Beto2828 |
| MITSUBISHI | TC2018PS | Channel locked asking for password | Unlock | 1) with the TV turned off, on standby, press the channel + key and then the channel - key (on the TV keyboard), the TV will turn on; 2) press the menu key until selecting the mode menu (when selected, the mode menu will be highlighted in red at the bottom of the screen); 3) using the function + and function - keys, select the lock function; 4) then, using the volume + and volume - keys, replace it from on to off; 5) press the menu or delete keys to exit the menu. I saw on other forums that pressing the volume-channel+ keys also solves the problem!... I hope it helps!... | Beto2828 |
| MITSUBISHI | TC 2018 | Functions locked | Open resistor r 725 -9k -pertodo micro | This email address is being protected from spambots. You need JavaScript enabled to view it. | |
| MITSUBISHI | TC1410 | Turns on after a few minutes the image starts to shake | Altered power supply 140v normal 114v see resistor r952, 270k | DJ PITUKA | |
| MITSUBISHI | TC-1410 1410 | The power turns on, it stays in stand bay, when you turn it on, the LED goes out | 6r8 3w resistor r571 open and cap c567 shorted on pin 9 line of the flay bak | Replacing the two components solves the problem | pedrinho cachoeirinha |
| MITSUBISHI | 2918 PS | Only stand by normal voltages | Changing the t552 transformer that powers the oscillator transistor. | T-552 just replace | Bynhoteck |
| MITSUBISHI | 2098 | Does not tune in to any channel | C124 and r155 changed and q111 q112 q113 also check | Test components c124 r155 q111 q112 q113 and replace | beto2828 |
| MITSUBISHI | TC 2919 | Does not turn on horizontally, heating up | D553 shorted | <small>This email address is being protected from spambots. You need JavaScript enabled to view it.</small> | |
| MITSUBISHI | TC-2099 | Doesn't start. LED flashing. | C907 (22x100v), power supply. | Eletrônica R-Tec | |
| MITSUBISHI | TC1498 | It doesn't turn on just the standby LED (it's never too much help, help you too) | TV had all normal power supply voltages except the 7.9v from h-vcc on IC101 | Tv did not oscillate horizontally without pulse on q551 glazed the entire stage of horizontal leakage on q203 2sc536kg replaced I discovered that tsound was no 7.9v on the collector I desoldered pins 36 and 37 ic101 returned 8v defect was ic101 tda8360 and q203 replaced ic101 tda8360 with a tda8361 it worked normally | jrezende |
| MITSUBISHI | TC 2918 | Blue screen shaking the vertical as if changing the vertical | Seletronic even with normal voltages +5 +30 volts | Replace it without a doubt | edezio eletronica |
| MITSUBISHI | KV2160B | Tv turns on normal sound without video power supply 9v from ic 682 ok check resistor r701 on kinescope board | Altered 470k r701 | eletronica muller | |
| MITSUBISHI | TC 2018 | Does not tune channels, noise in the audio, power supplys are all normal, plot with horizontal fixes, it seems that the image would be expanding vertically. | Channel selector | Replace the same. | arock |
| MITSUBISHI | TC-2099 | It doesn't turn on with a very low noise at the power supply, change the capacitor -c907, I changed it and I'm fine | Ss07 | joãotc | |
| MITSUBISHI | TC-1410 | The device works but the image shakes (goes back and forth) | Solution. measure the +b on top of the q-551 collector it must have 114 volts if it is above change the photo coupler and go for the hug. | Ademar Videira SC |