PHILCO TV Repair: Common Faults and Solutions.
Search: PHILCO
Results: 4741
Results: 4741
PHILCO Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
PHILCO REAL FLAT | TPF2940 | LED flashing and arming the protection | Opening the screen a little you notice retraction lines and then you arm the protection causing the led to blink | Replace 2 cap 5n6 / 1k6 c1701 c1703 | EPATEC-ES |
PHILCO | TP1453 | After turning on the TV, a line appeared on the screen and it turned off. | High power supply above 108 v | I replaced the 120k r 919 and everything was normal | ELETRONICA ROCHA |
PHILCO | PCM-2046 | It would turn on, the LED would flash, r720 was damaged, it would be replaced and it would burn again. | O problema era ic 601 tda-3653b | Changing it solved the problem, thanks | Eronaldo |
PHILCO | PSC 2952 N | When it turns on from high voltage and turns off | Changed the weak c - 712 6 k 8 / 1600volts | jaironuness | |
PHILCO | PCM-1466 | Image distorts in some channels | Changed c- 205 2.2/50 volts weak | jaironuness | |
PHILCO HITACHI | PC 1441 | The TV turns on and within seconds the vertical closes | Solution to the problem r 725 r 4r7 close to the flay back | FRANCISCO IVAN BASÍLIO - Ibiara - PB | |
PHILCO | 14CT6401 | Ripples at 110v | Altered waveform | Replace font scrs | paulo artur rio de janeiro |
PHILCO | PC 1427 U | Whistle when turned on, but inoperative | Power supply did not arm due to deficiency in filter component | Replace cap906,909,and diode905 | paulo artur rio de janeiro |
PHILCO | PCM 1448 | Turning off by itself | Dz 904 short | paulo artur rio de janeiro | |
PHILCO | TP 14U56 *** | No image check if tsound is power on the filament, when the screen increases it turns very faint white check if tsound is 180v in cap.c-713 if ok, note: rgb circuit must have 180v | Replace shock absorber | wagner | |
PHILCO | PCM 1443 EMOTION *** | Turning off white screen and retraces | R-715 c-719 | R-715 1r,subs 4r7 c-719 10mf x 350v | wagner |
PHILCO | TPF2130 | Does not turn on, without +14v pin 1 ic905 | Solda fria r931 18r 2w | BETO2828 | |
PHILCO | PCS 2078 NãO MARCA | Bu 2508 dx shorts out | C730 5k6 1kv6 changed and change original bu 2508 dx and increase c715 to 7k5*2kv | luiztvsom | |
TV PHILCO | PCM 2046 | Luminance- | Replaced the c716 10 / 250 volts | TV worked normally. | jaironuness |
PHILCO | TP-2053 | TV doesn't work std-by light blinks continuously but dimly | Changed the vertical output tda9309 | jaironuness | |
PHILCO | TP-1452N | When turning on tsound is no sound after a while the sound starts to come back hoarse. | Change the audio output | This email address is being protected from spambots. You need JavaScript enabled to view it. | |
PHILCO | TP-1452 | TV with normal power supply, when turned on it generates and cuts in 1 second | Check r713 of 1k8 changed | Daniel | |
PHILCO | PC 20R42 | Interference on the screen without video TV has sound | Replace c301 0.47/35 votes | jaironuess | |
PHILCO | PC- 20R42 ** | TV out of horizontal frequency | Or capacitor 303 of 47/35 votes was exhausted | jaironuness | |
PHILCO | TPF 2941 | It has a power supply but no gun | It fell, it was fixed, the trails worked normally; after two days it broke down, it was left alone in the waiting room | carlos branco |