PHILCO TV Repair: Common Faults and Solutions.
Search: PHILCO
Results: 4741
Results: 4741
PHILCO Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
PHILCO | TPF 2121 | Loud noise comes out of the speaker and protects LED keeps flashing | Diode d 909 shorted r911 r912 open | JOHNN | |
PHILCO | PCS 2976 | Does not work at 110 vts | Replace d 918 | Get separated | ELIZEU RIBEIRO |
PHILCO | TP-2052N 00000 | TV with bad tuning, image with drizzle. giving the impression that the seletronic is defective. | Filtro do if mf201 | I replaced it for one from scrap, defect resolved, hugs, I believe everyone is aware of putting their tips to everyone, professional friend | |
PHILCO | PCM 1452 | TV was oscillating but the screen was dark, adjusting the screen, a squeak came on the screen with a deficiency in one color, it was all yellow | Ci one (oscillator) was defective, I replaced it, it solved the problem | ozanan | |
PHILCO | TPF-2121C 00000 | Oscillates horizontally but after a maximum of 4 seconds it turns off, and the LED flashes; | Capacitor of { 6n8 1k6} as low capacitance ; | I replaced fixed braces blz!!! tec friends who are aware put their tips because everyone needs a tip shelter everyone | marcos melo |
PHILCO | TP2054 | This TV was turning on but with no image, just a line in the center, I thought it was vertical and it wasn't | 917 resistor without soldering at one of its ends, after re-soldering the TV started working normally again. | Moizes | |
PHILCO | PCM2044 | Fabric turns off intermittent. | C719 (10uf/250v) | Andrade Sequeira | |
PHILCO | PCM2044 | Does not work. stdby led is blinking | Shorted ic 401 (tda2613) | Andrade Sequeira | |
PHILCO | PCM2044 | Doesn't work | Zd901 is shorted.replace str50103. | Andrade Sequeira | |
PHILCO | PCM2044 | Dark screen | R716 (10k) | Andrade Sequeira | |
PHILCO | PCM2044 | Turns off every 5 minutes | D301 e d302 | Andrade Sequeira | |
PHILCO | PCM2044 | No contrast | C716, r706 e r717 | Andrade Sequeira | |
PHILCO | PCM 2044 CPH05 | When you increase the brightness, the TV turns off | Zd703 leak | Filipe | |
PHILCO | PCM 2044 CPH05 | When connecting an antenna, the TV turns off (protection) and when the brightness increases | Leaky dz-703 (power supply) | Luiz Filipe | |
PHILCO | PCS 2956N | Power supply does not weapon | 470uf Dry Low Supply Condenser | Elizeu | |
PHILCO | PC2027U | The power supply had a sharp and loud hiss. | C911 -> 4,7uf/160v. | This email address is being protected from spambots. You need JavaScript enabled to view it. | |
PHILCO | PCS2952 | It didn't change channels, the volume was muted and no OSD characters appeared, it just turned on and nothing else. | Ic1401-tda8425 was killing the memory sda leading to 0 volts after changing the ic1401 and ic1402-ha11508 the TV started working normally again. | This email address is being protected from spambots. You need JavaScript enabled to view it. | |
PHILCO | TP-2054 | Dark image, however, with normal menu on screen | Zd701 with leak (near the flyback - abl line) | Easy to detect. It is to measure the voltage +b 108v, if ok, measure abl -13v (you will notice that the abl line is low) | Tec VĂdeo |
PHILCO | TP1454 | Becomes completely inoperative | Depleted electrolytic capacitors, c914 and c918 | Adriano Cometti | |
PHILCO | TP-2054 | The TV is vertically closed (without deflection) and then goes into protection mode, remaining in stand by (turns off and no longer turns on) and the integrated vertical amplifier circuit is fault-free. | Change the c 614 caapacitor ceramic disc 47nx63v (473) | WAGGUINHO |