PHILCO TV Repair: Common Faults and Solutions.
Search: PHILCO
Results: 4741
Results: 4741
PHILCO Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
PHILCO | PCM2044 | When the TV was turned on, the image was shaking, and when the volume was increased, the image was even more shaky. | I checked the power supply and it was normal, but when I removed the capacitor from the power supply input I realized that it had a bad, rotten leg, the 400v/220mf c905 replaced it and went for a hug | This email address is being protected from spambots. You need JavaScript enabled to view it. | |
PHILCO | PCM1443 | Image blinking as if it were a stand by LED, normal frame, normal voltages, except video voltage; controls inoperative. | R713(100k) open. | Replace r713(100k), device ok. | clayton |
PHILCO | TP1454 | Problem with the colors, it remains without demagnetizing the kinescope. | Check the "epcos" brand component with placement number th 901. this component is connected together with the kinescope coil. | Just replace it with another one and go for the hug!!! | FRANCISCO |
PHILCO | TPF-2901 CP01RL01 | When turned on, it displays a white screen with horizontal retrace lines and seconds later it turns off. | Replacement of the 4r7 r711 that was open. | Marques | |
PHILCO | PCS 2700 | The TV turns off as soon as it was turned on | This TV doesn't oscillate without the fly back and without the deflector so it would be more difficult to discover the defect. | But in this case it was the bad deflector coil that was causing the TV to turn off | heliomar |
PHILCO | TPF 2130 CP 03 | Does not turn on, tsound is no + 14 vdc pin 1 of ic 905 | Change c 918 open | CARLOS ROCHA | |
PHILCO | PCS-2976 | Actuated protection It is with very high voltage | C715 or c730 changed | Henry Moura | |
PHILCO | PCS 3322N CP 01 LR02 | When turning off the power, it no longer turns on, only flashes, the power supply does not arm | Next to the wide capacitor switch c728 3n3 x 1600v | C728 3n3 x 1600v | This email address is being protected from spambots. You need JavaScript enabled to view it. |
PHILCO | PCM2976 | TV turns on after + or - 30 seconds, threatens to close the horizontal and turns off. | Probable cause, open power supply diode d917. | amsmariano | |
PHILCO | PCM-2046 | Jagged image | Interference on the kinescope PCI flat | Move the kinescope PCI flat away from the flay back as much as possible. | Wender |
PHILCO | DVT 100 | Doesn't spin the disc | R 23 of 1 r | Replace r 23 of 1 r | This email address is being protected from spambots. You need JavaScript enabled to view it. |
PHILCO | PCS2952N | Low power supply hitting the power supply transformer | Diode in4148 901 open | julio itaguai | |
PHILCO | TP2054 | When the TV was turned on, it started to show high voltage and then turned off and did not oscillate | I turned off +b from the flay back and the TV oscillated normally with the 109v input but if I turned on +b it stopped oscillating. | I tested the flay back in my test and it was bad without discharge, I replaced it and everything was fine | This email address is being protected from spambots. You need JavaScript enabled to view it. |
PHILCO PLATINUM | TP1452N | Does not turn on, inoperative, low voltage and oscillating on the horizontal transistor collector. | Change 1uf x 100v electrolytic located in the power supply. | FRANCISCO This email address is being protected from spambots. You need JavaScript enabled to view it. | |
PHILCO | TP1452 | Power supply pulsing, inoperative. | Check the 1uf x 100v electrolytic capacitor at the power supply. Just replace it with another one. | FRANCISCO This email address is being protected from spambots. You need JavaScript enabled to view it. | |
PHILCO | PCS2976S | Horizontal closing on the sides | 150k resistor near d irf ,n fir horizontal plate swap | Replace everything resolved | MARCOS MELO CASCAVEL CE |
PHILCO | PCR2049 CPH06 | Turns it on after a few minutes, it turns off or you turn it off, then it doesn't turn on anymore, it only turns on after a few minutes. | I verified that the horizontal output was experiencing unusual heat. | I replaced the 708 capacitor (471x2kv) and that's it. | Alvanyr |
PHILCO | TP1453 CP02RO | Philco tp 1453 TV with a drizzled image as if high voltage was escaping and switching off intermittently, I changed the flay and cleaned the capacitors horz. | R-917 2k2 | Open replace do not measure on the chassis | Schulz |
PHILCO | PVT1416 | Does not turn on, power supply drops voltage when trying to turn it on or placing a load | The power supply primary capacitors c504=47/25v, c538=1/160v | BRUSKE | |
PHILCO | TPF2121 | Sometimes it doesn't turn on | Resolve diode d 907 | Tip from your cÉzar | JOHNN |