PHILCO TV Repair: Common Faults and Solutions.
Search: PHILCO
Results: 4740
Results: 4740
PHILCO Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
PHILCO | PH42 A | If you made the same mistake as me, resetting with 062598 and tsound was no video, hold down the vol + and - keys simultaneously, plug in and keep pressed for 10 seconds | Tsound was no signal on the HDMI inputs, and a tip they gave me was to reset menu 062598 menu and it was bad!! I was left without video! | Rodrigo cofferi | |
PHILCO | PH28C20D JUC7 | Turns on the sound and turns off ci u807 117 1.8volts | You u807 | 1117 1.8volts | J marques |
PHILCO | PH21M SS | Colored stripes at the top of the screen | C301 (100uf x 35v) seco | Just replace | JS Eletronica (Nilsinho Rodrigues) |
PHILCO | PH21M SS | Cup effect | D454 (fr104) shorted | Just replace | JS Eletronica (Nilsinho Rodrigues) |
PHILCO | PH32U20DSGW | TV doesn't turn on, no STBY is turned off. | Short in the wifi network card. | Short in capacitor c54 on the board. | RNSPTEC |
PHILCO | PH40U16DSG | Doesn't start | Shorted fet transistor qp401 + shorted diode dp401 also change the secondary electrolytic capacitors | reginaldo moronte,eletronica junior caldas novas | |
PHILCO | PTV49F68 | Tsound is no sound on hdmi | Enter the menu, options, hdmi edid and change version 1.4 or 2.0 | MARIANO | |
PHILCO | TP1452N | Channels with black and white image. only one is colored | Color crystal not oscillating correctly | Replace the color oscillator crystal x502(3.575611 | flavio |
PHILCO | PTV43E60SN | Does not turn on back light | Remove qp411 close emitter collector on the board remove capacitor cb6 resolder the entire mentioned circuit and wash with esopropyl alcohol | Remove qp411 close emitter collector on the board remove capacitor cbb6 resolder the entire mentioned circuit and wash with esopropyl alcohol | central audio e video |
PHILCO | PH24M LED A2 | Inoperative without 12v | Z1 open 22v zener, I put a 24v one in place working perfectly | Measure outside because in place it looks good | NEI |
PHILCO | PH29M | Vertical with image in the middle of the screen | When turned on the image opens in the middle of the screen | Edvaldo Pereira Neto | |
PHILCO | PH28T35DG LED | TV works normally for a few minutes, when it heats up it turns off. | Check the cathode of d201, the voltage will have to be 3.3v, if it is below, or gradually decreasing, remove or replace c206. | electronicssupplyparts - Gramado/RS | |
PHILCO | PB500BT | Turns on for a few seconds and turns off the display and turns off the sound, returning to stand by | Ic 4, ht7533 on the display panel, replace the same one or another 3.3v regulator. Be careful with other regulators, as the input and output are different. | Ev antunes | |
PHILCO | PH21SS | It doesn't turn on, when it goes to activate it makes a noise and heats up the 22k r448 resistor, close to the deflector connector | Capacitor c441 de 240nf/400v | Replace it, which in this case was completely open | Romildo Behrend |
PHILCO | PCM-2046 | The TV worked normally but tsound was no OSD and tsound were white stripes on the top of the screen as if it were a bad 100uf/35v capacitor, in addition the resistor r614 had charred. | Vertical outlet ci with possible damage. | Replace the IC and resistor. (tec. edfersom, varjota-ce) | Edfersom |
PHILCO | PH32M LED A3 | Everything works after half an hour and the keyboard stops working. After +- an hour, the dsplay image stops working, the sound is normal, the LED lights up. | Solution modify r155 2r2 change 4r7 2w or 3w increase IC heatsink on the main board. | This email address is being protected from spambots. You need JavaScript enabled to view it. | |
PHILCO | PH24D20DMR2 | No image | Open fuse, dp6 diode with leak on the t-com board. q813 fet p channel shorted on main board | Djalma Moreira | |
PHILCO | PH32U20DSG LED | No image | Burning q808, p channel fet, close to the processor | C214, "10μF" on t-com board shorted. | Djalma Moreira |
PHILCO | PH39E37DSG | Does not turn on blinking stand by | Replace dp9 diode ba158 primary power supply | Replace dp9 ba158 diode | sergio |
PHILCO | PME22 Micro-ondas | The power button doesn't work and it's not the membrane | Leaky display | Leaky display. all segments light up, but when you try to press the on button, it doesn't come on. The solution I found, since I didn't find the display available and changing the board was unfeasible, was to place a diode (1n4007) in series with the shorted pin, with the cathode connected to the display and the anode on the track. To identify which pin, just release one by one until the microwave turns on, in my case it was the first pin on the left next to the CN6 connector. | Miratec Eletrônica |