PHILCO TV Repair: Common Faults and Solutions.
Search: PHILCO
Results: 4741
Results: 4741
PHILCO Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
PHILCO | PME22 Micro-ondas | The power button doesn't work and it's not the membrane | Leaky display | Leaky display. all segments light up, but when you try to press the on button, it doesn't come on. The solution I found, since I didn't find the display available and changing the board was unfeasible, was to place a diode (1n4007) in series with the shorted pin, with the cathode connected to the display and the anode on the track. To identify which pin, just release one by one until the microwave turns on, in my case it was the first pin on the left next to the CN6 connector. | Miratec Eletrônica |
PHILCO | TV PTV43E60 | TV turns on but the LEDs on the screen keep blinking | 470k RB10 resistor in the LED driver changed to 510k, it is close to the LED connector | Ariel Santos | |
PHILCO | PH29C | Tv works - vertical closed | Ic301 | Replace ic301 stv8172a =la78045 | EMERSON RIBEIRO |
PHILCO | PH39N91D | Doesn't turn on anything, power supply primary is dead. | Ci position oscillator nw901 | Changing the ci position nw901 | GL Eletrônica - Contagem MG |
PHILCO | PH24M LED A | When turning on the TV, it turns on gold, the screen lights up white, changes to yellow, blue, green, becomes striped and turns off but no image appears | Dirt and oxidation on the main flat cable | Cleaning the cable contacts or replacing it | LEVY SOUZA |
PHILCO | PH28S63D | With sound and no image, dark screen | Led defect, 1 led with change but not open and not in Kurdish | Bad defect to find, if you test it with a "homemade" LED tester you won't notice the defect because they all turned on normally, apparently it wasn't an LED. With the power supply adjustable to 5v, I powered the LED, then I only found 1 replaced, I replaced it and the TV started working again. LED on the middle bar, next to the charging connector | Claudio Jorge Eckert Junior |
PHILCO | PH39F33DSG LED | Turns on, works a little, the screen LEDs start to blink and go out, it appears to be an LED defect | Causes ts 2 power supply transform with cold welding | Ariel Santos | |
PHILCO | PH24M LED A2 | When plugged into the socket, it flashes stand by once and does not turn on | Ic u4 | Ic u4 | RONALDO VIEIRA |
PHILCO | TP2920 | It turns on standby, turns on the power button, it starts and then disarms, but the circuit remains partially connected. | Change two polyester capacitors located on the board next to the main one. c1703 and c1701 | ||
PHILCO | PH51U20PSGW | It doesn't turn on, it just stays on stand-by | Apparently it would be a software update, but it was the faulty power supply board | Replacing the power supply board | Arnoltec |
PHILCO | PH400N | Normal stand by you turn on the volume button it turns blue but nothing works | Probably shorted usb reader board and card reader | Release the 2 whips that go to the plate. These two functions will be lost but the device will work again | Magalhães |
PHILCO | TP 2054 | Image warping and turning off | Low primary power supply | Swap d918 and zd908, at the power supply near the c.i. 901 | eletronica fernandes |
PHILCO | PH43E30DSGW | Does not turn on, nor does standby light up, no signal at all | Main board shorted at 12v and gnd, in the qcpass sector, 2 smd capacitors were shorted, c18 and c19. | The smd capacitors c18 and c19 were replaced, and the problem was solved, it started working normally again. | Adriel SS |
PHILCO | PH40E60DSGWA | Does not turn on black light | Short in the LED power supply | D81 | Eletrônica Morais |
PHILCO | 40U16DSG | Inoperative, no standby, 12v as soon as it turns on it appears then drops | Qp401, dp401 in short. obs dp401 on this TV was hbr3200(200v,3a) replace it with the one indicated in the mur460(600v,4a) diagram | lgmendes | |
PHILCO | 40U16DSG | Inoperative, no standby, 12v as soon as it turns on it appears then drops | Qp401,dp401 shorted. | lgmendes | |
PHILCO | PH21MSS | Turns off and goes back to standby | Tl431 trace | Francisco | |
PHILCO | PH21SS | Heating r.816a, r818 and q802, zd805(11v) with 8v. | S826 47/25 | GDP2 | |
PHILCO | PH51U20 | Without image, with the voltages va and vs | Oxidized control board | Plate replacement | Alex Lopes <small>This email address is being protected from spambots. You need JavaScript enabled to view it.</small> |
PHILCO | PH 21MSS | Cushion effect image with vertical curves on both sides | In my case it was in the ew sector of the TV. After a lot of racking my brain I ended up discovering the toasted l451 position coil. | Coil l451 of the ew circuit. (note; in most cases it could be the d454 fr104. good luck and I hope it helps you in some way. | D.S.E.Eletronica |