Search: PHILIPS
Results: 14173

PHILIPS Repair Guide: Common Issues and Fixes

Brand Model Fault Detailed Problem Solution By
PHILIPSGL1019
+ b instead of 70 v it had 30 v and it didn't turn onBelieve me short sound output tda 7052Replaceloantonionobrega(patos pb)
PHILIPSVARIOS MODELOS
TV doesn't work, keys don't work, control doesn't work with the factory message89 keyboard and OSD on controlThis email address is being protected from spambots. You need JavaScript enabled to view it.
PHILIPS29PT4641
L04U
Vertical open only the bottomSmd resistor 3465 and 3464, the chassis only has one of the resistorsjedvaldo
PHILIPS20PT3331
Turns off in a rowCause: 1k 2318 smd capacitor defectiveklein
PHILIPS32PFL3403
Turns on and off randomlySubstituir as r 602,603,604Place 01 1m resistance in place of the threeELETRO CENTER
PHILIPS150S
Turns on and off, sometimes holding down the keys works for a while and then turns off.Defective digitsReplace all digitsValmon
PHILIPS29PT4631
Lines top of imageC2480 and c2487 obs. exchange bothThis email address is being protected from spambots. You need JavaScript enabled to view it.
PHILIPS29PT5642
The TV turns on right after it turns off and goes into protection, the image does not appear, but if you increase the screm, a vertical strip appears, not in the center, further down, but vertically closed.R3606 auterated 56k resistor supplies the 5v to the hercules.Resistor replacement.play back
PHILIPS20PT3331
When you turn on the TRC it turns green and then turns off (it goes into protection)Poor contact on the r g b e board (in other cases it is the socket)Soldered the whole board and it works normallyDIGITEC ELETRONICA Lambarí D'oeste -MT
PHILIPS32PFL3404
With sound without imageCf01220nThis email address is being protected from spambots. You need JavaScript enabled to view it.
PHILIPS14GL1319
GR1-R03
Weak video, no contrast, image varying, does not fix the effectOpen resistor r3215Calixservice
PHILIPS21PT5433
This TV had no image, only sound, and turned off in 5 seconds.Checking the voltages, the voltage of 5 volts was not found on her ht so I checked the beautiful heart which comes out of pin 5 of the flay back and passes through two resistors 3443 and 3444 both of 1Ω and goes to the diode 6444The problem was the resistors 3443 and 3444 which were completely broken, I just replaced them and the 5 volts came out on the TV and the image went out in the fileThis email address is being protected from spambots. You need JavaScript enabled to view it. de governador valadares
PHILíPSPFL3403
Off, no stby. power supply zeroed.D2 rectifier bridge and 5a fuse and 1a fuse.The rectifier bridge and fuses were replaced.Sérgio luiz martins
PHILIPS20PT3331
No audioCapacitor 2444 low capacitanceCapacitor replacedIbar
PHILIPSPVT461
No writing (OSD), sometimes there isCapacitor inside l 1802 with leakRemove the coil, remove the capacitor from inside it, replace the coil, and place a 27pf capacitor on the outside, on the printout, on the corresponding pinsjasvan souza
PHILIPS20PT424
Turns off when antenna or av is placedCauses 12v 6413 zener diode with leakageklein
PHILIPS21PT9467
This TV arrived with the vertical closed, the customer says that smoke came out when checking the vertical outlet, it was burnt, I replaced it and checked the other components, everything was ok. I turned on the TV and it worked fine, but after about 5 minutes it started to close with several scratches in the center of the image. I removed the deflector, cleaned it well with thinner and applied varnish, it was ok.Vertical and deflective outlet.RAIMUNDO
PHILIPS20PT120
PT
Turn on the key and the LED turns on. Press the channel button and the LED flashes about 5 times but it doesn't work. the lid lights up againIn my case, I just had to resolder the c2442. and it was ok.C 2442EDM- ARARAQ.
PHILIPSFWC505
No sound comes out of the speakers, only the headphones.Replace, transistor bdw94, in position 7317This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILIPS14PT3131
No soundThere is a diode at the output of the assembly that is bad and it is unnecessary and only to finish it can the technician release itAUGUSTO