PHILIPS TV Repair: Common Faults and Solutions.
Search: PHILIPS
Results: 14174
Results: 14174
PHILIPS Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| PHILIPS | 21PT5433 | Low sound (very low) | Swap c2444 470/16v | Beto Eletronica | |
| PHILIPS | PT3336 L03.6L | Vertical stroke and turned off | R 3448 | juci | |
| PHILIPS | 20PT 3331/78 | No sound when turning on the TV after some time, the sound returns but is low. normal image. | Changed the c 2444 capacitor with low capacitance. This capacitor is close to the fly bak, for those who don't have the schematic. OK. | jaironuness | |
| PHILIPS | 29PT4641 | Does not turn on, and the stand-by LED does not light up | Change coupler photo | ||
| PHILIPS | 20PT4331 | Vertical beam | 7466,7464 7463, the 7464 was shorted but the protection did not activate, after replacing it went into protection due to the 7466 and 7463 | Dj carlinhos | |
| PHILIPS | 20PT4331/78R | Turns on the TV, horizontal RGB lines appear, vertical lines are slightly closed and then turns off. | Capacitor 2460 (663k 250v) | Edson Peixoto | |
| PHILIPS | 21PT5433/78R | Burning horizontal output - intermittent | Get straight to the point. Replace the deflector coil. case solved | Otecnico.20m.com | otecnico |
| TV PHILIPS | 20PT 120 A/ 78 R | TV doesn't turn on | 8444 leaky exchanger. | jaironuness | |
| PHILIPS | 29PT4631 | Serrated or sawtooth image | Changed resistor close to bc's 337/327 | Replace r3493/ 5r8 | cesar_unitec |
| PHILIPS | 20PT326A/78R | When turned on, it generates high voltage, the filament lights up, but it does not shine or sound, emitting a noise similar to a cricket. | Ic 7600 | The replace of the same | nonato |
| PHILIPS | 20PT326A/78R | Turns off when turned on, remaining on standby | Resistor 3470 18k open vertical protection | Replace of the same | nonato |
| PHILIPS | 29PT4640 | When you turn it on, it turns off then, after insisting several times it works | Pre-horizontal filtering | Ronie Grein | |
| PHILIPS | 20PT3336/78 | Normal OSD, dark screen and sound on the channels | R 3459 and r 3442 open (both 100k) | ELETRONICA ESTUDIER | |
| PHILIPS | 14PT1556 S L01.2E AA | No image. There is no brightness/contrast control, adjusting voltage doesn't help either. | There is no information eht. resistance 3431 at output 8 of the tr.linhas (ehtinfo) burned out. | Raúl Faustino | |
| PHILIPS | 29GX1895 ANUBIS | The image keeps shaking, there are times when it turns on normally, but if you turn it off and on again, the same defect appears (reduced frame, OSD repeated on the screen) | Diode 6199 bzx79-c5v6 on the side of the subwoofer | Check the bc548 next, and also the tip42c | ANDRE |
| PHILIPS | 14PT3336 | It has a power supply but it oscillates and goes out | R 3445 open | miro eletronica | |
| PHILIPS | FW-C505 | No sound, exit ci ok | Ic 7501= tda7468d smd, pins 14 and 15 must have 4.8v if it is low check this clk and data line | BRUSKE | |
| PHILIPS | 20PT 3331/78 | Vertical lines with interference at the top of the screen | Changed the c- 2460 68 k/ 100 volts | jaironuness | |
| PHILIPS | 29PT554A L9 | Image stretching to the left, tuning with low signal | The defect was because the power supply was low, I changed the position from the l5550 to the l5576, no power supply output, it was at 130v, I changed it to 140v, the TV was beautiful | Reversing the position of the l 5550 p l 5576 tv looks great | marcos melo[ CASCAVEL CE ] |
| PHILIPS | 20PT3331/78 | Vertical closed | Changed the 10/250 volt c- 2465 | jaironuness |