PHILIPS TV Repair: Common Faults and Solutions.
Search: PHILIPS
Results: 14168
Results: 14168
PHILIPS Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| PHILIPS | HTS3510/78 HTS3510 | Turns on switches functions, but no audio comes out or increases volume, normal power supply voltages | Low voltage in memory u16, replace diode d1 | Replace diode d1 | home theater |
| PHILIPS | 32PFL3707D/78 | Turns on and off, sometimes it stays for a short time and turns off | C9111 | Changing the 330f/16v capacitor without measuring, I put 470f/16v in its place and it worked | Maike Sorriso-MT |
| PHILIPS | 32PFL3404/78 | Turns on normally but keeps restarting by itself. freezes image and the characters are scrambled. | I cleaned around the processor and fixed the problem immediately. Good to change the capacitors too. | RYK | |
| PHILIPS | 42PFL4007G/78 | Customer complained that the TV turns off by itself. I noticed that sometimes when I turned off the TV it wouldn't turn on at first and I would have to unplug it to turn it on again. | Regulator u701 g1084-33 has to output 3.3v and was at 4.5v. I changed it and it was a perfect test for a few days. | Credits for electronicashow. I got the tip on YouTube: https://www.youtube.com/watch?v=zbyfiusynm4 | RYK |
| PHILIPS | 32PFL3403 | Does not turn on, nor does stand-by | Pin 2 of ic901 (fad back pin) pulsing but with voltage below 5v causing ic901 not to act. | Replace q903 (2n7002 smd mosfet transistor) with leak. | Gênios Eletronica SJ SC |
| PHILIPS | 32PFL3007D | Tv mort | When you disconnect the cable from the main board, the 5v returns, when you connect the cable, the 5v drops to 2.7v, if you inject 5v from an external power supply, the TV turns on normally, I connected the board outside the TV, I plugged in 5v with PON and the 12v and 24v appear normal | The defect is the capacitor c933 on the power supply board, it is on the 5v line, 330μF by 16v, I replaced it with a 470μF by 25v, perfect | Claudio Eckert |
| PHILIPS | GA312 | It doesn't stop at the end of the album | Change the 10n capacitors on the board, the 470x63 one on the power supply, and the LED that goes on top of the LDR close to the arm tower. | The LED becomes weak with age, and dry capacitors only get in the way. When the record reaches the end, a metal piece closes the LED light under the LDR, the record player goes into stop mode, and the solenoid raises the lift. | Trendset |
| PHILIPS | 40PFG4109 | The backlight turns on, but tsound is no image. | 17v supply on the vcom board shorted. | Measure short on capacitors cd6, cd7 and cd8. (one of them shorted) | Persio (TVCompany) |
| PHILIPS | 40PFL5605 VAN GOGH | Turns on, backlight comes on and tsound is no image. | Regulator 12v position 7kfe | electronicssupplyparts - Gramado/RS | |
| PHILIPS | 42PFL4007/78 | Turning off by itself after being turned on for a while or not turning on at all. | Ruim 3.3 volt regulator, (u701) regulating 4.3 volts | Replace the regulator | Alex Lopes <small>This email address is being protected from spambots. You need JavaScript enabled to view it.</small> |
| PHILIPS | FMW352/BK | No sound from audio output | Transistor q30 causing mute on pin 10 of the tda8947j | Q29, q30 and q31 had a leak from emitter to collector greater than that between base and emitter. | Márcio Alves |
| PHILIPS | 14PT316A/78 | It doesn't turn on and blinks, you hold down the channel key and the screen blinks (vertical) | C i of vertical tda9302h defective | Replace the tda9302h or equivalent and go for the hug (be careful with the Chinese virus, stay away)...... | Paulo Sertel - Itararé - Sp |
| PHILIPS | DVP 3820K | I'm sound | Ce 882 (220×16) | NEW PEK ELETRÔNICA | |
| PHILIPS | 29PT8457/78 L04 | Expanded image, cushion effect. | Transistor shorted base emitter, 7484 bc847b smd. it is next to 7406. | After changing the TV ok. | George Pontes |
| PHILIPS | 49PHG5000/78 | Blurred image. | After changing the main board the image became blurry. | Enter the numbers using the remote control, (062598, house, 160) Attention, observe the screen code that is located on the label of your TV model. | AGILDO MENDES (MENDES ELETRONICA) |
| PHILIPS | 49PHG5000/78 | Inverted screen and blurred image | Right after the main board was replaced, the screen showed a blurred image and an inverted screen. | Access service mode (menu,1999, return) 1st- navigate to option 74 (flip panel), press the right arrow on the remote control to enable the option (flip panel from off to on. 2nd- navigate to option 19 (virgin mode), press the right arrow on the remote control, enable the virgin mode option, turn off to on, then turn off the TV using the remote control and unplug it for a few seconds. | AGILDO MENDES (MENDES ELETRONICA) |
| PHILIPS | 49PHG5000/78 | Inverted screen and blurred image | Right after the main board was replaced, the screen showed a blurred image and an inverted screen. | Access service mode (menu,1999, return) | AGILDO MENDES (MENDES ELETRONICA) |
| PHILIPS | 40PFL3606 | Increasing volume alone. | Miniature smd capacitor as leakage | Remove leaky miniature SMD capacitors on the main PCI, in the line of connectors that go to the sensor plate | Imagem |
| PHILIPS | 32PFL3403 | Does not turn on, lacks 3v3 and burning ic901 | Trafo tt901 it has to have between pins 5 and 6 5 homs, if it has less it will be defective, it will burn the ci 3bs02g | Just replace the t901 and the chopper | guinga sdia goias |
| PHILIPS | HTS3531/78 | Turns on, the name philips appears, then the name standby appears and philips appears again, it stays in this loop | Dvd tray belt | Just replace the belt | Gleyton |