PHILIPS TV Repair: Common Faults and Solutions.
Search: PHILIPS
Results: 14168
Results: 14168
PHILIPS Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| PHILIPS | 20PT3331/78 | Turns on and off with closed vertical, | See the voltage of the 33v that goes out to the varicap, in my case it was the broken track, the 33v arriving at the varicap, but it didn't go to the other side, | DJ PITUKA | |
| PHILIPS | 40PFL5615D/78 | Dead power supply | Diode d907 shorted. just change and celebrate the result | ELETRÔNICA CENTER | |
| PHILIPS | 20PT3331 | Normal power supplys and does not oscillate | Resistor in position 3445 | Replace the component | fofao wr |
| PHILIPS | 32PFL5604 | TV turns on and off with the control, turns on normal backlight but no image | I noticed that the 12v voltage was missing in the lvds signal cable that goes to the screen, it was only 2.5 volts | Testing the ci ekfa = fds9435a on pins 1,2,3 it had 12v and on pin 4 = 5.4v on pins 5,6,7,8 only 1.49v and even changing pin 4 the voltages at the output did not replace, and it was resolved after changing this ci dai on pin 4 = 0v and on pins 5,6,7,8 =12.4v and 15.5 volts arrived on the lvds cable | BRUSKE |
| PHILIPS | 32PFG4109 39PFG4109 47PFG4109 | Locked in logo | Processor bga solders with poor contact | Reballing | davi.sls |
| PHILIPS | 32PFL3606D | Completely white image | On the tcon board a resistor in position 3j26 of 240k is open. Just change and run for the hug. | Daniel Dega | |
| PHILIPS | 32PFL3406 | Blurred image | Change power supply because only 20 volts arrive on the inverter board when 24 volts should have reached | NENO This email address is being protected from spambots. You need JavaScript enabled to view it. | |
| PHILIPS | 29PT9467C/78 | Noise popping from speakers with TV on standby | Replace 1000x25v capacitors c627 and c628 | ||
| PHILIPS | 32PFL6615D/78 | Turns on but no image | Fuse - 1kfa open on the main and a ceramic capacitor shorted on the main, tsound is no visible reference on the board for this capacitor, its location is on the top of this 4r5 coil reference 5kag, this capacitor is connected to pins 2 and 4 of the ci reference 7kac. d | I jumped the fuse and removed the capacitor and the TV worked normally. | ELETRONICA JUNIOR BELEM PARA |
| PHILIPS | 43PFG5000 | No image with sound and backlight on | This is the second TV of this model that I have fixed with the same defect, this time the c103 has a short. | The tip is to take voltage measurements before changing components because on the first TV the defect was at c 218 and this time it was c103 | marco.320 |
| PHILIPS | FWC270/19 | Turns everything on normally + sound comes out loud | Smd transistor position 7502 | Replace or jump between emitter base | Juniornbk |
| PHILIPS | 42PFL3403/78 | The stand by LED lights up and accepts the power on command. But the relay does not engage or close but voltage appears on the relay coil re1. and the coil resistance is normal compared to another relay from.same.tv | Change re1 because even with the normal coil it can be altered | @gepe | |
| PHILIPS | 42PFL3707D/78 | It doesn't turn on, it has 5v and pwr-on ok. | Pfc not oscillating, 310v on the input electrolyte capacitors, the right one is 380v | Replace ic9801 (r2a20113) e q9801 (stf24nm60n) | PEDROTEC |
| PHILIPS | 40PFL9605D | Turns on and off LED flashes 9 times check voltage of 15 volts if it is normal on the tcom board if it is defective and the voltage does not change. on the input and not even on the ci fet 1102 fds 9435 resolders the bga. | Bga gets cold solder over time due to heating ic301 | A reflow was performed on the bga ic 301 with flow and temperature between 320 and 350 degrees for 3 minutes. Wait for the plate to cool, clean it, remove excess flux, assemble and turn on. go for the hug | Adriano Miranda |
| PHILIPS | 42PFL3604 | Does not come out of standby | C 474 on main board | Miratec Eletrônica | |
| PHILIPS | FWP2000 | Power supply completely dead, device completely inoperative | The ic706 was not acting, it enters ac but does not send the pulse to activate the mosfet oscillation | Replace ic706 (tny277) problem solved | Dr eletronics |
| PHILIPS | 32PHG4900 | Inverted image after changing the board | Access service mode (menu+1999+return). 1st navigate to option 74 (flip panel), press the right arrow on the remote control to enable the flip panel option from off to on. 2nd navigate to option 19 (virgin mode), press the right arrow on the remote control, to enable the virgin mode option, from off to on or from on to perform both tests. Turn off the device using the remote control. wait a few seconds and turn it on again. | Mine only worked in of not in on as tsound are many tips | beto2828 |
| PHILIPS | 21PT5437 | Closed vertical at the top with colored lines and turning off | D6460 shorted | Replace | Marcondes Ohm Eletrônica Jaicós PI |
| PHILIPS | 29PT9467C/78 | Two transistors shorted in rgb | Q904 e o q905 | Replace the q904 which is the a1015 the base is right and is negative and the q905 which is the c1815 the base is right and is positive! | Sinailson furtado |
| PHILIPS | 29PT9467C/78 | Two transistors shorted in rgb | Q904 e o q905 | Replace the q904 which is the a1015 the base is right and is negative and the q905 which is the c1815 the base is right and is ne | Sinailson furtado |