PHILIPS TV Repair: Common Faults and Solutions.
Search: PHILIPS
Results: 14173
Results: 14173
PHILIPS Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| PHILIPS | ANUBIS-S | Protection of part of eeprom | Protection of part of eeprom ---------------------------- for all versions: for software number 1 (6k no txt) and software number 2 (8k txt) address 255 should be filled with data 232 after replacing the eeprom. this to make sure the right part of the ee | ||
| PHILIPS | ANUBIS-S | Powers supply output voltages for the different sc | Powers supply output voltages for the different screensizes for anubis-s aa/bb/cc/dd ------------------------ for adjusting the power supply output voltage (via r3512) following survey gives an overview of the values for the different screensizes of all c | ||
| PHILIPS | ANUBIS-S | Plop sound at switch off of the set | For mono versions: replace d6109 by bzx79-c2v7 (5322 130 34563) for stereo pb (+ btsc) versions: replace d6807 and d6808 by llz-c2v7 (4822 130 81138) remarks : introduced in production week 9331 | ||
| PHILIPS | ANUBIS-S | Plop at switching on/off nicam sound | In case of a nicam switch on/off plop it is recommended to change on the nicam module (diagram k) of the anubis s bb: * place elco 47uf 20% 25v (4822 124 40433) with + to pin 9 of ic7075 and with - to ground * replace c2065 and c2076 by 470nf 10% 50v ( | ||
| PHILIPS | ANUBIS-S | Plop at switching on/off nicam sound | In case of a nicam switch on/off plop it is recommended to change on the nicam module (diagram k) of the anubis s bb: * place elco 47uf 20% 25v (4822 124 40433) with + to pin 9 of ic7075 and with - to ground * replace c2065 and c2076 by 470nf 10% 50v ( | ||
| PHILIPS | ANUBIS-S | Pix blanks at certain prog. nrs | Software bug. micro processor need to be replaced. change from version sa fhv 1.9 to sa fhv 2.1 | ||
| PHILIPS | ANUBIS-S | Picture width too small during off-air reception. | Delete r3453, r3454 and l5454 in the line defl flyback circuitry and place jumper at position 9454. remarks : introduced in production week 9340 in spore and week 9346 in lfl thailand. | ||
| PHILIPS | ANUBIS-S | Picture tube 20" anubis s aa and cc a48kxr98x | Picture tube 20" anubis s aa and cc a48kxr98x (4822 131 20577) --------------------------------------------------------------- only for anubis-s 20" aa and cc for both anubis s aa and cc picture tube a48kxr98x (neutral hemisphere) is no longer available | ||
| PHILIPS | ANUBIS-S | Picture jittering when osd is recalled, all versions | Replace r3605 by 2k (4822 116 52253) at pin 20 of up remarks : introduced in production week 9328 | ||
| PHILIPS | ANUBIS-S | Osd characters too thin | It is recommended to replace in the control part: r3715 by 1k2 (4822 116 52207) remarks : introduced in production week 9408 | ||
| PHILIPS | ANUBIS-S | Only for anubis-s bb 25" codenumber information | Only for anubis-s bb 25" codenumber information ---------------------- the missing service codenumber for the bridge coil l5480 in the east / west part of the 25" anubis s bb (diagram aa) is: 4822 157 71149 | ||
| PHILIPS | ANUBIS-S | Only for anubis-s bb 25 adaption in the frame par | Only for anubis-s bb 25 adaption in the frame part of 25" anubis s bb --------------------------------------------- from production start onwards the following modification is done in the convergence circuitry in the frame part of diagram aa: r3403 shou | ||
| PHILIPS | ANUBIS-S | One colour missing or no picture | In case of 1 colour missing or no picture, it is recommended to solder across r3301 on the crt panel on the copper side: 100nf 10% 250v 4822 121 41689 this capacitor protects the 3 bf422 video output transistors ts7305, 7318 and 7327 against flash rem | ||
| PHILIPS | ANUBIS-S | No stereo, no +95 volt | R3523 is interrupted, d6519 and c2519 (= capacitor between d and s-7513) are short circuited. remove c2519. replace r3523 - 390k - 4822 116 52278 replace d6519 - btz03-c15 - 5322 130 31574 | ||
| PHILIPS | ANUBIS-S | No picture after picture tube flash over | In case after a picture tube flash over (one of) the video output transistor(s) bf422 (ts7305, ts7318, ts7327) failed, it is recommended to: 1. change 2337 to 4n7 2kv 4822 126 12833 2. delete and short r3336 with a wire jumper 3 | ||
| PHILIPS | ANUBIS-S | No picture | Apply a slight force to further insert the eht cable into the line output transformer 5445. remarks : above cure is only relevant for sets with lot 4822 140 10525 or 4822 140 10557. when replacing the above mentioned lot's, please take note of t | ||
| PHILIPS | ANUBIS-S | No nicam sound | In case of no nicam sound it is recommended to replace on the nicam panel: r3055 to 560Ω 2% 0.25w 4822 051 10561 (diagram k page 21 in the service manual anubis s bb 4822 727 20262) remarks : lower r3055 gives a higher starting current fo | ||
| PHILIPS | ANUBIS-S | No colour at pal in case of disconnected 2cs+i/o+ampl panel | In the service position, the main panel of the anubis s bb is disconnected from the 2cs+i/o+amplifiaction panel. for anubis s bb sets with 2 hef shift register in cascade (as how it is used by now for controlling an anubis s bb set with incredible stere | ||
| PHILIPS | ANUBIS-S | No +95v/+115v from power supply | In case of a failure of one of the components ts7513, r3503 or d6502 till d6505, it is strongly recommended to replace all of these components. for service codes see, service manual anubis-s aa gb 4822 727 19707 e 4822 727 19719 anubis-s bb | ||
| PHILIPS | ANUBIS-S | Modification | Modification ------------ for all anubis-s with no secam reception ic7225 tda8362 is replaced by tda8361 in all anubis-s sets with no secam reception possibility from production week 9416 onwards, so, ic7225 = tda 8361e/n3 4822 209 33479 (pal + ntsc, n |