PHILIPS TV Repair: Common Faults and Solutions.
Search: PHILIPS
Results: 14169
Results: 14169
PHILIPS Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
PHILIPS | 29PT4640 L01.1LAC2K3 | Dark image with traces and small clicks on the tube plate, (tsound are several clicks per second, 5 times or more) and these clicks are reflected in the image, that is, when the click occurs the image becomes clearer. | I found r3481 and r3482 open, I also changed r3465 and the image improved but tsound were still crackles, but it was because of the screen being out of adjustment, it was just a small adjustment and that was it, the crackles disappeared and the image was perfect. | This email address is being protected from spambots. You need JavaScript enabled to view it. | |
PHILIPS | DVP 320BK | It only stays on standby, LED indicator flashes or turns on and off in seconds | Low supply voltage, 7v5 zener with leak and exhausted capacitors on the secondary | Replace 6622, 2221 and 2210 | Felipe Farias |
PHILIPS | 29PT554A | Doesn't even turn on the stand by LED | Changed d6540 had 5 volts on pin 1 of ic 7520 | Replace d 6540 | juci |
PHILIPS | FWM593 | Sound i am | R611 e tr q632 | Just replace it and move on to another one. | eletronica vieceli |
PHILIPS | 20PT122A | Av doesn't work | Enter service mode ground pin 1 memory | Replace to av 01 | ELETRONICA MAURI JUNIOR |
PHILIPS | CTN-BB | Does not do standby | Replace smd transistor position 7601 | Ruyzovich | |
PHILIPS | CTN-BB | Red image with return lines | Replace smd transistor position 7644 | Ruyzovich | |
PHILIPS | CTN-BB | Does not start LED blinks | Replace 12Ω resistance in power supply position 3521 | Ruyzovich | |
PHILIPS | CTN-BB | Does not adjust contrast | Replace resistance (3460) of 10k | Ruyzovich | |
PHILIPS | CTS-AA | Vertical problem, image shrinks when changing scene | Change r3461 from 8k2 | Ruyzovich | |
PHILIPS | CTS-AA | Image stretched to the right side and does not fill both sides horizontally and does not tune | Replace o ic stv2246c | Ruyzovich | |
PHILIPS | 20PT529A/78R | It turned on after it got too hot or didn't turn on at all | Capacitor 2410 470 nf/16v | I replaced it and it worked perfectly | marcelokvaco |
PHILIPS | 14PT110A 78R | Does not turn on (does not oscillate) only in standby and normal +b lines. | Change eeprom memory. | jayjunior | |
PHILIPS | 21PT9467C78 A4 | Volume goes down to zero and doesn't go up but | Microprocessor tda 9376 | Replace and mediation | eletronica pai e filhos escada |
PHILIPS | DVP 3320K | Turns off after 3min | Ci tny176pn pos u1 | VICCARI | |
PHILIPS | 29PT4636/78 L01.1L AC 2K3 | This TV sometimes turns on 3 attempts or more when it turns on it has a serrated sound | Bc337 bc 327 c2455 c2405 worked normally | antonio dos santos lima | |
PHILIPS | 21PT5435 0000 | TV with +b ok but it doesn't oscillate, it doesn't turn on. | Regulator 7493 of 3.3v altered p/ 5.5 = 78l33 | Replaced it and everything was ok!!! good luck! | Jhone Eletronica |
PHILIPS | 21PT9467C/78 SK4.1L | Vertical deflection only halfway down. Half up, some colored streaks appear | Vertical ci power supply ok (+15v and -15v), vdra signal sawtooth ok, vdrb deformed. | After several tests, vertical CI replace, cold test of several components, defect was d351 ba158. Tsound is no point in measuring, you have to replace directly. test c352 100μF/50v which may be altered. | Renato Pareta |
PHILIPS | 20 MT 21 31/78 | It doesn't turn on and the stand-by LED is stuck, it oscillates when you press power on the remote control. | ,I checked the good condition of the soldering on the pins of the large integrated ci- 7200,even though it was in good condition, I carried out a careful re-soldering,this device is so difficult to maintain,it started to work perfectly, ok !!!!!!-- | ELIZEU RAMOS | |
PHILIPS | MONITOR 150S6FS | Functions frozen, dark screen | Unlock by pressing and holding the ok key, after message enter my color change until image appears | warley cesar |