PHILIPS TV Repair: Common Faults and Solutions.
Search: PHILIPS
Results: 14169
Results: 14169
PHILIPS Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| PHILIPS | 40PFL3805D/78 | TV doesn't turn on | D-210 d-510 q-501 r-517 u-501 f-101 | Replace them all | EDILSON AZEVEDO |
| PHILIPS | 21PT5456 | Turns on with normal image. then turns off. | Change c 2444 of 470 x 16v in the filament line | edimilson de osasco | |
| PHILIPS | 14PT316A L9.2A | Turning off in 5 seconds if you hold the channel button + TV it stays on if you release it it turns off | Transistor 7620 bc547 button side channel | Replace | BETO2828 |
| PHILIPS | 29PT9467 | Suffered an electrical discharge | Replace r-3532 ,ic 7531tea1620 | WARLEY CESAR | |
| PHILIPS | 21GX1666 | Image all jagged and shaking | Replacement of 47uf 160v c2448,c2447 capacitors | julio.sertemaq | |
| PHILIPS | HPS- 2185 | Doesn't turn on anything, totally inoperative. | The stand bay LED does not light up and the secondary transformer has very low voltage | Swap c808. | lou |
| PHILIPS | 29PT4631 L01.1LAC 2K3 | Does not tune uhf | This defect is caused by the eprom, just adjust it! | Enter service mode, in the option menu, if op 1 is set to 0, replace it to 128, exit service mode and tune again. | This email address is being protected from spambots. You need JavaScript enabled to view it. |
| PHILIPS | 29 PT L03. IL | Without video with lines, but with characters | R 3442 open on fback pin 10 | Tonin Coxim MS | |
| PHILIPS | 14GL1014 | Black screen no image no drizzle | C2410 no pé do vertical 100uf 25v | Replacelo | antonio nobrega(patos pb) |
| PHILIPS | FWM416 | I'm sound | Amplifier on level under pin 13 of the stk433-870 | Replace q721/716 2n5551=mpsa42 e q722 bc556 | VITALTEC |
| PHILIPS | 16GL1333 | Low 5 v supply, screen with retraces, no image and sound | Ceramic cap 2953 short | pardalzito | |
| PHILIPS | 20PT424 | The LED keeps shaking and horizontally | Adjust +b in power supply | Agnaldo | |
| PHILIPS | 21PT9467 | TV does not turn on, only standby access | I checked the power supply first, everything ok, secondary diodes, everything ok. bad flayback.. I changed the flayback, more vertical closed, replaced ci tda4865, changed the diodes, capacitors and resistors of the negative supply line of this ci and the 185v line | Replace of flyback + vertical output + capacitors diodes and resistors of the negative line of the tda8565 and the 185v line | Fenixtec |
| PHILIPS | 29PT4643/78 | Dead power supply | D 6536 | Replace it | TIAGO.ELETRO |
| PHILIPS | 42PFL3604 | Don't tune in | Bad selector/varicap. Note: tsound is no 33v power supply requested in the manual. | Replace selector/varicap | |
| PHILIPS | 42PFL3604 | Does not turn on, stays on standby | Capacitor c806 sem carga. 4.7uf/400v | Replace the capacitor | LUCIO |
| PHILIPS | 20PT336A;78R | The filament turns on, gives a flash and turns off | 100uf25v and 1uf50v capacitors both power supply close to the 3540 trimpot | Replace both, both were dry, very low capacitance | janilson |
| PHILIPS | 14PT218A | Menu appears on the screen and does not obey commands | C 2006 with escape. the same is on pin 80 of the micro | Replace it or withdraw it | antonio vinicius alexandre nobrega |
| PHILIPS | 28PW6532/78R | When you turn it on, it turns off and on, off and on... | Bcs 337 and 327 replaced by bd139 and 136 | manin | |
| PHILIPS | 20GX1656 | Image with small waves, almost serrated | Ver c 2531 | Master eletrônica |