PHILIPS TV Repair: Common Faults and Solutions.
Search: PHILIPS
Results: 14169
Results: 14169
PHILIPS Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| PHILIPS | 29PT4635 | Doesn't start | D-6467 / d-6464 (smd aberto) | Replace with 1n4148 | This email address is being protected from spambots. You need JavaScript enabled to view it. |
| PHILIPS | 20PT3336/76 | Dark screen with characters; and normal sound | 100k open resistor r3442 | DIEGO LIMA NOVA TIMBOTEUA PA | |
| PHILIPS | 20PT3331/78 CH | Turns on with three colored lines and a closed image at the top of the screen and turns off. | I replaced the c2460 and adjusted the screen, the TV started working normally again. | Marcelo Sperb | |
| PHILIPS | 29SX8879 | Completely stopped | R 3136 =820k open | ramiresrc | |
| PHILIPS | 29PT6566/78 SL04L11 | Normal image, sound hissing on all channels, I didn't hear any voice, if I increase the volume, the hiss only increases. | Enter service mode and change audio qss from on to off | hndrsn | |
| PHILIPS | 29PT 552A | If no power supply, or just the LED blinks | Can be c2463 220/2kv or c2550 with small leak | Remove, for testing, if it works, replace. | jasvan souza |
| PHILIPS | 29PT552A | Measure, if bad, replace | C2551 and c2450 with good appearance but exhausted (47/160v both) | Measure, if bad, replace | jasvan souza |
| PHILIPS | 29PT552A | Measure, if bad, replace | C2551 and c2450 with good appearance but exhausted (47/160v both) | Measure, if bad, replace | jasvan souza |
| PHILIPS | 40PFL6605 | Does not turn on, nor does the stand by LED light up | D911/d907 diodes (sb260), as I couldn't find these diodes I put the sb560, it worked perfectly. | These diodes are on the secondary of the power supply | Mauriílio |
| PHILIPS | 20PT 326A/78R | Ñ league. | Capacitor 2409(47uf/160v) e capacitor 2551(47uf/160v) | Replace them. | BARRETO CRUZ |
| PHILIPS | 37PFL5332 | Turns on the image appears for 15 seconds and turns off | U-202 change without measuring | VIDEOTRON | |
| PHILIPS | 20PT324A L9.2 | Very weak channel reception | Filter 1003 (m1967m) | joaomvjr | |
| PHILIPS | 21PT9467C SK-1LCA | Turns on with image and no sound, doesn't turn on, locks keyboard, turns on only with drizzle or white screen. | Zd604 | saffier | |
| PHILIPS | 29PT5645 | No image | Shorted picture tube | Replace tube | ELETRONICA MAURI JUNIOR |
| PHILIPS | 20PFL5122 | Tsound is no image, the lamps do not light up | A faulty light bulb triggers the protection and no one lights up | You need to replace it with a good bulb to avoid triggering the protection, just leave it off | eletronicaaeb |
| PHILIPS | 20GX1669 | Does not turn on LED blinks 2 times | Ci vertical | Tda8351 | ELETRONICA MAURI JUNIOR |
| PHILIPS | 21PT1663 L7.2E | Doesn't start. LED blinks weakly and without voltage at the power supply output | C2550 | Substituir c2550 | jose almeida tavares |
| PHILIPS | 25PT5321/11 GR2.4 | When turned on, the image appears for 1 or 2 seconds, then the screen is dark with return lines and a light line at the top. If you change the screen a little, the video tends to appear very dark. | One of the kinescope's cathodes is nearly short-circuited. in my case it was blue (I tested the cathodes with a rejuvenator). | Use a kinescope rejuvenator to eliminate possible short circuits in the cathodes. | AleVict |
| PHILIPS | 29PT4635/78 | White lines across the screen as if it were normal high sound screem and it doesn't turn off.l | R3477 from 150r open. | hndrsn | |
| PHILIPS | GR 1045... GR1L1I-VA- RO3 | After changing the fly back, only the LED and the 35V power supply blink. | +12v protection activated | Raise d6904, if it works, put a 13v one | jasvan souza |