Philco TV Repair: Common Faults and Solutions.
Search: Philco
Results: 4811
Results: 4811
Philco Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| PHILCO | TP 1453S | Black stripe on left side | Capacitor 718(102k por 1kv) | Replace capacitor 718 | DTEC-ELETRONICA-Massapê-ce |
| PHILCO | PH 29 | It turns on for 10 seconds and turns off, sometimes it turns on and then turns off | V574, (in the test it is good, but in operation it changes) and c450 (681 x 2kv) | Replace v574 e c450 | DTEC-ELETRONICA-Massapê-ce |
| PHILCO | PH39N91DSGWA | After changing the main board the image is blurry | Heda/weight | Update or remove r2 from the vcom board (panda385r display) | Renato |
| PHILCO | PH32C10DG | Update | Can't find any update on the philco website | Use an update from another model, the ph32c10dsgw works in its place, the boards are the same, drivers.philco.com.br/tv/hkc/ph32c10dsgw | Capiroto |
| PHILCO | PTV43E3AA | Entered without image, only LEDs on | Defect in the tcon, resoldering in the integrated circuit, and the voltage pwm | Just resolder and run for hug, cold solder, I soldered them all with a thin tip. it was fillet | Elison48 |
| PHILCO | TV PH32E32D LED | TV freezing, no sound, sound failing | Change ca815, ca804 and check u804, u805 and u807 | Eletrônica Barbato | |
| PHILCO | PCS 2976 | It turned on, no image appears and then turns off, the standby LED flashes | Cap 715 (2k2- 2k5volts), exhausted or low capacitance | Replace and run for the hug | DTEC-ELETRONICA-Massapê-ce |
| PHILCO | PH-672 | I'm sound | Q1, transistor that does the mute, remove. | tecnardi | |
| PHILCO | PH32U20 | Doesn't start | C997 and or c1000 short | Obs fet 809 and replace the caps... 10μF16v | Eletronica tensao R, Jacuipe |
| PHILCO | PH28N91DSGW | Locked in logo | Software // felipe t. | Software update | TAVARES |
| PHILCO | PH32U20DG LED JUC7.820.00101170 | It takes a long time to turn on, I had to press the power button 16 times to turn on | +b 12volts pressing | Capacitors cp201 and cp205 semi exhausted | Ivan p santos |
| PHILCO | PH42M61DSG | Dead, no standby | After a good amount of analysis, I replaced ci fr9889 in positions n801 and n802 | Claudio Jorge Eckert Junior | |
| PHILCO | PH29E63D | Plug it into the socket and it goes straight from the red LED to green and doesn't do anything else | Regulator u8 1117 cdefective can be changed even if it gives 1.5v and it turns back on | Replace u8 1117 1.5v regulator and it works even if it gives 1.5v replace | Beto2828 |
| PHILCO | PTV32G70RCH 0000 | Doesn't turn on, everything is off | Capacitor smd curto ce25 | Replaced resolved..... good luck! | Jhone eletronica |
| PHILCO | PME31 MICROONDAS | Burning fuse | Everything has already been seen and analyzed. capacitor, diode, gate switch, magnetron, board relay and everything is ok... be suspicious of the trafo. | Changing the transformer, even when testing and when cold. The replace was made and the fuse stopped blowing... | JC Eletrônica Cícero |
| PHILCO | PTV42E60 | Locking during use, makes a noise when shutting down when it locks | Malfunctioning rectifier bridge | Changing the rectifier bridges, tsound are two, located next to the capacitor. | FILIPE FURTADO |
| PHILCO | PTV42E60 | LED on sound and TV with no image, no 12V power supply to the screen. | Ql01 defective | Ql01 defective (it is under the processor heatsink) I replaced the capacitor cl06 with discharge | FILIPE FURTADO |
| PHILCO | PH40N70DG | Backlite lights up but tv doesn't generate image | Capacitor d8 on vcon shorted | Replace D8 | wander teixeira |
| PHILCO | PH39F33DSG | Turning off by itself after about 5 minutes | High heating in viper17 | Viper17 defective, replace and run to the hug | CDS_DIAS-LEDTECH |
| PHILCO | PCX16000 | Turns on, everything works, but no sound | Ic5, 3v6 regulator, low voltage | Shorted ceramic capacitors, c25, cn07 | MP ELETROINFO |