Philco TV Repair: Common Faults and Solutions.
Search: Philco
Results: 4811
Results: 4811
Philco Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| PHILCO | PH50A17DSGWA | Don't turn on or flashing | power supply Primary Defect C.I UW1 | replace for C.I P6005 of AOC TVs, but needs to feed pin 3 with 10m resistor from the alternating power supply similar to pin 5 feed | JhonatanSG |
| PHILCO | PTV32D10N5SKH | connect with normal picture. and gradually falls to led teesan. Until it erases. | replace without testing the capacitor PEC501. 47/100V | ||
| PHILCO | PH55E20 | Fully stopped, no led stand-by | power supply defect, R7 1K close to the two large capacitors in the middle of the plate | Sylvox | |
| PHILCO | PH21M SS | LED flashing and doesn't start | IC802 TL431 | To replace | Eletrônica do Gilvan |
| PHILCO | PH39N91DSGW | Sometimes it lights standby and calls and sometimes does not light up or call | CW926 with escape | CW926 | Bhtechcenter |
| PHILCO | TPF2940 | Don't turn on, flashing STB | C1701 very altered | replacement | paulo r barbosa |
| PHILCO | PH32E31D... | It works on picture. Defect similar to screen, but it is plate | Q13 transistor burned. Next to the flat cable connector that goes to the screen. | Israel portela | |
| PHILCO | PTV32G60 | LED current | Remove resistors | Remove RB15 and RB14, next to the LED connector | Eletrônica Cecé, Brumadinho MG |
| PHILCO | PTV32G60SNBL LED | Do not light backlight, the LEDs | Electrolytic CB2 120UF X63V | Eletrônica Cecé, Brumadinho MG | |
| PHILCO | PH42M2 | No Led Light Lights Weak | When the led lights up the TV does not turn on / gets tight to the TV Normal | The LED lights weak and the TV does not depart, if you take off and put the LED back on and the TV works normal. If testing the power supply has perfect voltages but no. The IC U201 (Viper17) is the cause of the headache. | oskarala |
| PHILCO | PTV50D60SA | Call soon or not even turn on the back light! | Intermittent bl-on coming from the main | TRANSISTOR SMD QB2 NPN IN THE MAIN PCI, very close to the Micro Dipper! | BRAMBILA |
| PHILCO | PH42M LCD | Does not turn on, 5v standby oscillating | EC3 capacitor, (100uf x 35v) exhausted or high esr | Stiltec | |
| PHILCO | PTV43E10N5SF Versão AV | TV inoperative without standby | Vod2 and Vod3 | replaced the photo coupled 817c and also the TL AS431A and the TV worked perfectly. | Sinailson furtado |
| PHILCO | PH46 LED A2 | Sometimes it turns on, sometimes it doesn't turn on | 5v regulator position Q100 on the main board | Replace circuit and capacitor next to it c199 and c117 | Duarte Eletrônica |
| PHILCO | PTV39E60SN | The TV turned on normally, went beyond the logo, stayed on for a maximum of 1 minute and turned off. When removing the power cable from the LEDs, the TV remained on. Tests were carried out on the buses, all ok. | LED power supply ci did not meet the need for LED power supply, causing the TV to return to Stand by | Replace the ub1 IC located next to the LED connector. | DL ELETRO |
| PHILCO | PH40U16D8G | Turn on LED drive, but tsound is no picture | Shorted CD8 capacitor, VCON board | Replaced the Capacitor | Joao Carmo |
| PHILCO | PH32F33DG | Does not work.led stby off. | Tsound is no 3.3v power supply | See, replace D406 3.3v power supply protection. (Diode shorted) | Arock |
| PHILCO | PH200N | League display off | Zd5 and zd4. Q17 shorted | Dinetronic This email address is being protected from spambots. You need JavaScript enabled to view it. | |
| PHILCO | PTV50N10 | THE PHILCO LOGO APPEARS AND ADD THE picture | CAPACITORS DEPLETED AT THE power supply 22uf / 250v | ANTONIO BATISTA - MAX SOM ELETRÔNICA - BH | |
| PHILCO | PH43C21P | It has all the power supply voltages but the stand-by LED does not light up | IC 802 step down 1.2v regulator in short, solution to replace the IC or adapt a step down plate regulated to 1.2v | replace the ci 802 or adapt a step down plate set to 1.2v | Eletronica Moura |