Philco TV Repair: Common Faults and Solutions.
Search: Philco
Results: 4740
Results: 4740
Philco Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
PHILCO | PH40U16DSG | Backlight turns on without image | Shorted capacitor on the vcon board! cd8! abs | Replace of the same | Rafael Sena |
PHILCO | PH29MSS | The TV turns on in service mode with bugs in the letters and characters and does not tune the channel, the volume is at maximum, it does not enter the AV and it has a child lock after turning off the TV, it goes into protection mode | I replaced the tda11145ps microprocessor and the 24c16 memory with a 21mss one and the TV was like new | ||
PHILCO | D28D27 PH2827 | The LEDs don't light up | At the power supply | Marcos | |
PHILCO | PCM-2051 | Turns on normally, image shakes and then turns off (varies depending on scene and brightness) | Altered abl | Open smd resistor on the abl line - r707 - 1k | |
PHILCO | PH21M SS | Press the keyboard TV turned on without image making a noise when putting +b 115v and flayback heating up | Flayback | Replace o flat back | |
PHILCO | PH40D10DSG | After changing the LED kit. the logo appears and turns off | Update error | First of all, check the 3.3 v voltages on the regulators (tsound are 3 on the board) if everything is ok. update the software, (you can buy it on the free market) tip, when updating, put the pen drive with the TV unplugged, hold down the power key and plug it in, when the blue screen appears you can release the key, don't turn it off until it's finished the process | ENGETRONICA |
PHILCO | PH14C VERSÃO ``C´´ | Little contrast or it does not work | Vd461 1n4148 shorted close to the fly back | Replace vd461 and run to the hug | EDIVAN ELETRONICA |
PHILCO | PTV43E60SN LED JUC7.820.00207831 | Power supply with 12v output, oscillating between 1.2v and 17v after a lightning strike in the network | Changing ci tl431 position up2 | PATRIARCA | |
PHILCO | PH21M SS | Screen closed and mute | Rewrite the eprom memory. | EDIVAN ELETRONICA | |
PHILCO | PH32B51DSGWA LED | Dark image looks like dim or burnt LEDs | 470 x 25v capacitors and 100 x 63 puffed cap | Ariel Santos | |
PHILCO | PH32B51DSGWA LED | Dark image looks like dim or burnt LEDs | 470 z 25v capacitors and 100 x 63 puffed cap | Ariel Santos | |
PHILCO | PTV58G70RCBL 0000 | White screen with black spot bottom right | Short display | The famous tape to remedy it lol.... ffc2 tcon connector I isolated 12 last copies; slept... good luck! | Jhone eletronica |
PHILCO | MSP 201 PR | It only stays on standby, the LED is on, it doesn't turn on | Change all touch keys | Resolved | milton santos |
PHILCO | PH32M | Blinking light bulbs | 24 volt power supply, it was like 22 volts | Regulator u2 replaced..to ensure I replaced optocoupler p3 (power supply board) | Maurilio |
PHILCO | PTV40E21DSGW | TV works ok but when it turns off and on again tsound is no audio | My case was made software update | Update tv via usb | Adriano Silva |
PHILCO | PH229N | It didn't turn on, it just turned on the LED | Change the radio/off/cd, mp3, usb, sd, pc and aux in selector switch. | ||
PHILCO | PH24D21D LED B | Tuning analog and digital channels only audio without video "flat screen, menus ok" | Update, did not accept via usb, only eeprom rewrite | Eletroserv | |
PHILCO | PH39N86DSGW TP.MS6308 | Backlight turns on/off | Remove rb837,rb838,rb839. | Replace rb837 of 1r5 with 3r3 and rb of 2r2 with 4r7 | Multimarcas/Acarí |
PHILCO | PH32U20DSGW | Doesn't start | Powering the secondary with a 12 v x 2a power supply, the TV turned on normally, so my defect was in the primary, I found the DP202 was leaking | Replace, I took it out of scrap. | Maurilio |
PHILCO | PH39N86DSGW | Does not turn on, power supply stopped | Ci position ub101 short, the schematic doesn't mark which ci it is, I didn't find information anywsound. | I put an ld7536 and it worked. optocoupler and kia431 were shorted too. | André |