Philco TV Repair: Common Faults and Solutions.
Search: Philco
Results: 4740
Results: 4740
Philco Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
PHILCO | PH21M SS | Image only of the upper half of the screen and with stripes | D301 vertical com problema | Replace diode d301 in4007 | ELETRONICA KLEIN |
PHILCO | PH49F30DSGW | It turns off by itself, sometimes it doesn't turn on and it keeps blinking on stand-by. | Photo coupler position uw2 with leakage. | LABOTRON | |
PHILCO | PVT OU PCS | Turns on and then turns off | Cold solder on the wires that go to the tube plate, on the 180v line | MARCONES DE ARARIPINA-PE | |
PHILCO | PH40R86 | LW802 coil heating up fell into the TV | Change caps cw908 and cw922 100uf 63v (I put a 470ufx100v one)...lw802 coil (101) is shorted...I put a 150uh wire taken from scrap...it didn't heat up the lw801 coil anymore | I went to the crowd lol lw801 cw908 cw922 | Alextecnico |
PHILCO | PH21MSS | Inoperative nor does the STB LED light up | Power supply with 50v memory power supply with 1v | Remote control sensor | REAL ELETRON CARVALHOS MG |
PHILCO | PH29E63D | Turning off sometimes squeaking | Cold welding in the u50 power supply region | Good thermal blower solves it good luck | Jhone eletronica |
PHILCO | PH24T21DMT | Does not turn on, standby on. Sometimes it turns on intermittently when it wants. | Software update | Download the two files on the pen drive, follow the update procedures. | Giovani |
PHILCO | PH32M5 | After a while when turned on, the backlight turns off and the sound remains | Cold solders on the power supply board. give a good review of the most relevant welds | Lucafer | |
PHILCO | PH42M30DSGW | Erased from everything | Ci n802 has input voltage but does not output 5 volts | Tsound n802 | Jg eletronica |
PHILCO | PH32U20DSG LED | Does not tune channels | Regulator u001 ams1117-3.3 changed voltage below 3v | Replace u001 ams1117-3.3 | ELETRÔNICA DVN |
PHILCO | TV PH39N86 VERSãO A | TV turns on, the logo appears and then turns off | Possibly the inverter controller but I couldn't find it for purchase | Remove rb873 and rb838 and go for the hug | Marivaldo |
PHILCO | PB329BT | Crackles in the sound after minutes of use on the FM function. | Defect, lack of grounding on the x2 crystal close to the fm antenna. | Solution, solder the crystal housing to the board's ground. | Eletrônica EMB |
PHILCO | PH40D10DSGW | Does not turn on and no stand-by | All normal voltages except for varicap +3.3v_tu and tun_3.3v (between 3.05) | Capacitor cp205 (on the old assistance, it bumped and the solder cracked) | lucian oliveira 61991271532 DIGITAL TECH |
PHILCO | PH21MSS | The LED turns on, presses power, the LED turns off and turns on again, with a hissing noise that seems to be coming from the flay-back. | Vertical output with leakage from pin 4 to 5, c829 and c601 stuffed | Replace and please God | Daniel |
PHILCO | PH32E32 | LED is on and won't turn on | In my case it was not the 1v8 regulator but rather the 3v3 (u805) with low voltage. I changed it and it worked ok. | Lucafer | |
PHILCO | PH21 M SS MA1 | Power supply goes up to 20v and returns to standby | Flay back | Replace without testing | Paulo santana |
PHILCO | PH40D | Turns on, works for a minute and turns off | Software update | Software update | Rodrigo cofferi |
PHILCO | PH24M LED A2 | Turns it on, lights up the screen, stays for a while and goes out. normal sound, LED bar off. LED bar ok. | Ci bit3251 led bar power supply controller. pin 5 works with 0 volts and it was 0.28 volts, this is the circuit protection pin (ovp) | Replace the 10k resistor that goes from pin 5 of the ci with a 3k3 resistor so that the circuit drains this small voltage to ground. | DL Eletro Caxias |
PHILCO | PH39N91 | Inoperative, standby off. very low power supply output voltages | Cw926 4.7mf 100v at power supply. change without measuring. | Republishing a colleague's tip | Lucas |
PHILCO | PH39N91DSGWA | The remote control doesn't work | Replace capacitors c1 and c2 on the tv sensor board with 1000 micro by 16v | Marcelo |