Philco TV Repair: Common Faults and Solutions.
Search: Philco
Results: 4740
Results: 4740
Philco Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
PHILCO | PH32E31DG LED | TV turns on the bus and turns off immediately and doesn't even show the Philco logo | Capacitors with altered values | Changing capacitors c2d7,c1d9,c2d6 50v/100 | Nando Cell |
PHILCO | PH32U20 | When turning on, the logo appears and returns to the STB | Firmware | I tried updating with a pendrive, but it simply didn't recognize the file, I had to rewrite the nand with the file: dump - 4shared< /a> | Davi.sls |
PHILCO | PH800M | Led standby piscando | Short on the 3v3 line | Sd/ms/mmc card socket shorted on the 3v3 line, I looked for a short and realized it was on the card reader housing, simply cut the 3v3 line on the socket board | fabiusmax |
PHILCO | PH49U32SDGW | When turned on, it turns off after 36 seconds | Software update | RoqueCipriani | |
PHILCO | PH20U21D LED | Does not even turn on standby | After observing that the primary power supply was oscillating, I realized that tsound was a short on the 12 v line. | C736 em curto. smd de 10μF | GR Eletronica |
PHILCO | PH28T35DG PH28T35DG LED | I'm sound | Change c622 and r621 10r next ci exit. | Replace c622 and r621 10r next ci exit. | CENTRAL AUDIO E VIDEO |
PHILCO | PH40D10DSGW | Does not turn on and does not turn on standby. When measuring the secondary power supply, the voltages are pulsating. | DP202 diode (SMD Shotky) with ok measurement. I replaced it with a new one and it solved the problem. | PIXEL ASSIST | |
PHILCO | PH39U21DSGW | Burning LED bus | Voltage of 100.6 volts drops to 95 after removing resistor rp411 (2r2) | Remove rp411 from 2r2 close to the connector of the wires that go to the bus, once this is done it drops to 95 volts.... | MIGUELTV |
PHILCO | GLASS | Turn on and off | Capacitor ec1 of 4.7uf 400v empty | The replace was carried out and the kettle started working again | chaleira elétrica |
PHILCO | PH32F33 | Nothing turns on, inoperative | Change ci tea1733 on the power supply board primary | Alex | |
PHILCO | PH49F30DSGWAC | Does not turn on, no standby | Changed optical coupler uw2 and ci pwn uw1 killing the voltage. | Replace both components. the ci pwn is the ld7536. | NiloTech Eletro Eletrônica |
PHILCO | PH4930DSGWAC | Does not turn on, no standby | Changed optical coupler uw2 and ci pwn uw1 killing the voltage. | Replace both components. the ci pwn is the ld7536. | NiloTech Eletro Eletrônica |
PHILCO | PH42E53SG | Standby on, turns on, no backlight, does not turn off power | C122 na placa tcon | Replace with one of the same size | ToniTec |
PHILCO | TV PH32M LED A4 | Turns on sound and normal image after a few minutes it becomes silent. | Replace c823 remove q809. | Carlos Rocha. | |
PHILCO | PH21SS | Reduced frame voltage of 113v low or varying | Rp551 2k tripot oxidized or open defective | I replaced it for a 2k2 because I couldn't find a 2k one and went for the hug | orlando lott |
TV PHILCO DE 29 | TP29C21 PCIB0004 REV. | Defect was the power supply made a noise and did not arm, it was accumulating charge d915 with leakage | Defect in the primary power supply | Era d915 | CLAUDIO ROBERTO |
PHILCO | PHT660N | Does not turn on, low power supply, panel off | Capacitors with esr (they measure normal on the capacimeter but the esr meter shows the defect), change without testing e1, e2, e10 e9 e11 e31 e5 e3, e21, e26 open r20 | HAHNRAHN | |
PHILCO | PHT660N | Does not turn on, low power supply, panel off | Capacitors with esr (they measure normal on the capacimeter but the esr meter shows the defect), change without testing e1, e2, e10 e9 e11 e31 e5 e3, e21, e26 open r20 | HAHNRAHN | |
PHILCO | PTV50D60S | Doesn't start. only flashes standby LED | Short on the main board, killing the 5v supply. By injecting voltage into the shorted line, the processor would heat up. | RTD2968 processor replacement. As tsound is no BGA soldering, it is easier to find the processor and replace it. Another solution is to replace the main board. | GABSENS |
PHILCO | PTV32C30D LED | I changed the board, it kept changing colors (rgb) | On the remote control press vol+ or vol-, or menu, or pause, or exit. in my case it was the exit key to unlock. Fits various Philco models | Eletrônica Cecé. Brumadinho MG |