Philco TV Repair: Common Faults and Solutions.
Search: Philco
Results: 4740
Results: 4740
Philco Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| PHILCO | PCS2976 | Power supply with 150 volts making the horizontal width increase a lot instead of 130v in the power supply there was 150v | R919 changed to 139k | After putting in another 120k r, it started working again with 130 volts and with the normal horizontal width | josé gusmão |
| PHILCO | PCM 2044 CPH 05 | Turning on and off blinking the LED without functions | Release pin 35 of the micro (protection pin) if it works correctly check r713 near the flyback | In my case it was r713(100k) open | antonio nobrega(patos pb) |
| PHILCO | PCS-2168 | Does not tune channels, adjusts the tr201 coil and does not solve it. | Replace c 205 2,2 micro 50v colocar 4,7 50v | Eronaldo | |
| PHILCO | TP-2920 | Turning off after a certain time on, as if arming the protection. | Secondary voltages were not stable due to photo coupler failure | Replace the photo coupler | celinds |
| PHILCO | PCM1444 | Difficult to turn on, sometimes the LED blinks and also bad tuning | Capacitor ruim c725 | C725 replacement | Sandro .T. Grachet |
| PHILCO | TPF-2901 | Fly was bad and after changing the flyback there was no video | Dz801 shorted and q622 shorted | Replace it. | renatoquecho |
| PHILCO | TP29C21 | Distorted image and passing the vertical bar | 9volt regulator with heating | Changing the ic905 in the secondary power supply | eletronica fernandes-to |
| PHILCO | TP 2054 **** | When I plugged it into the socket, the LED came on, but it wouldn't start, I looked at the r-724 10k burnt out, I replaced it but it didn't solve it, I checked the power supply +b was normal, when I pressed on/off it dropped to 16 volts, I replaced the flay back, it worked normally | Defective flay back and burnt r-724. | Replace | wagner |
| PHILCO | TPF 2130 | Stop, all normal power supplys except 3v3 | Ic 804 | Replace the ic 804, in my case I removed the original which is a lm 317 and inserted a 7833 regulator, the only adaptation I made was to the grounding | Roberto Consertos |
| PHILCO | TPF2121 55 02 F 6949 020 | Burning ts horizontal | I can't even watch it, it's already burning | antonio | |
| PHILCO | TPF2121 55 02 F 6949 020 | Burning ts horizontal | I can't even watch it, it's already burning | antonio | |
| PHILCO | PCS 2976 | When turning on the flayback it makes a leaking noise and then turns off | C715 = 8n2 | Replace without testing | Danieleletronica |
| PHILCO | PC-1443 | Bad or distorted image like an old model that has to adjust the horizontal @@@ | Adjust coil LR201, if that doesn't work, check c205=2.2uf/50v, c905=220uf/400v | Help yourself, leave your tip ass.arni | ELETRONICA ARNI-LEOBERTO LEAL-SC |
| PHILCO | PCM 2046 | Dark image | R717 open | I replaced it back to normal image | carlos w |
| PHILCO | PCM-1451 CPH-06M | Reduced frame (intermittent), no color in palm. | Ic501 tda8841 faulty | Replace ic501 | Silvio Tur |
| PHILCO | PCS 2976 | Burning horizontal outlet | Q702 leaking | To replace | niltron |
| PHILCO | PCR 2049 | Dark screen with sound | C709 | Changing the c 709 there is no point in testing it, it is next to the horizontal output | itan ( cabeça) |
| PHILCO | TP1410 | Does not turn on, just stays on standby and arms and disarms | Cold solder on r931 | EletroClaudio Aguas Belas Pe | |
| PHILCO | TPF 2130 | TV stopped LED off relay does not arm and power supplys pulsing with all values below the specified | Check r927, photo coupler, ic 903, c 925 some of it was possibly faulty in my case the pro was on c925 and r 927 I changed it and ran to hug | Roberto Consertos | |
| PHILCO | PCS 2952 | Turns on and protects goes to stand by | Capacitors c 711 e 712 altered | Debique |