Philco TV Repair: Common Faults and Solutions.
Search: Philco
Results: 4740
Results: 4740
Philco Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
PHILCO | TP 2052N | Straight and thin line lying in the center of the closed vertical kinescope(tube) | Replace ic - 501 (tda- 8842 2y ) | BARRETO CRUZ | |
PHILCO | PCR - 2049 | Turn on the TV, the LED lights up then turns off but it doesn't turn on | Change without measuring c- 708,704 de471k/2kv - c709 de 152k/2kv and c- 913 de 1uf/100v | BARRETO CRUZ | |
PHILCO | TPF2130 | Blocked channel | General password 7685 | Type 7685 and then enter the menu and deactivate the function | |
PHILCO | PC 1444 | TV kept blurring the image and interfering with the sound (squeaky) | Ceramic capacitor c 203 on the fi line, shorted | Replace capacitor | afonso Eletronica taquari |
PHILCO | TP-1452N | TV does not work when turned off and making noises at the power supply | Capacitor,position,c913=1mf/50v | I replaced it and plz | ELETRONICA MEDEIROS |
PHILCO | PCM 1444,1446,2044,2046 | Works normally with screen and LED blinking like a solution | R713 100k open | I replaced it and resolved | antonio dos santos lima |
PHILCO | PCM-1444 -1446 -2044-2046 | Running away from color, sometimes you want to scroll vertically but it's not enough to scroll the image half tremola | C205 | I replaced c205, 208, 702 solved | antonio dos santos lima |
PHILCO | TPF29S4F | It doesn't turn on, it just stays on stdby, sometimes it sets up the power supply and sometimes it doesn't work, it seems like a bad contact but it isn't. | 3.3v low supply | Substituir q903(bc337-25) e zd902(zener 4,7v) | NARDINHO |
PHILCO | PCS2952 CPH06 | Activating the protection and then turning it off and with +b180v with 260v | Causes depleted width capacitor c711 and c712 | klein | |
PHILCO | PCM-2046 | Blue screen, no sound but normal osd. | C-722 470x16 | FERNANDO S | |
PHILCO | PCM-1444 | Running away acor, or a hundred color pb, | Zd504 5v1. can you put the dz4v7 it works ok | GLUJ SAT Eletrônicos | |
PHILCO | TP-1454 | Tv inoperative | Transistor fet switch shorted conducting and killing fuse | Replace of the same | jayjunior |
PHILCO | PCM 2046 | Out of sync | 2.2uf/50v electrolytic capacitors near the ci one chip. | Replace of the same | jayjunior |
PHILCO | PC-1444/2044 | No synchronization turning on. after a few minutes the image becomes normal. | C-205, c-409 of 2.2x50 and c-722 of 1x50 (electrolytics) | FERNANDO S | |
PHILCO | PC-1444/2044 | Severe noise in the sound, normal image | C-722 = 470x25 | FERNANDO S | |
PHILCO | TP1454 | Faulty vertical...horizontal output getting very hot | Change the circuit ic601 tda9309.... place a 12r resistor between the base and emitter of the horizontal output transistor | FUBULHA-PI | |
PHILCO | PCM1444 CPH05 | Does not open the vertical, good ci, there is no 2.8 volts on pin 43 of the ic-501 | Check if the r-802 12k resistor is open | If said resistor is open, replace it. | Paulo Sertel Itararé SP |
PHILCO | PCM1443 CPH05 | Horizontal K (again) | C-709 10nx100v open (no capacity) | Replace it with a new one and a hug | Paulo Sertel Itararé SP |
PHILCO | PCM2043 CPH05 | There is sound, there is an image but the LED blinks and there is no voltage on the protector | The r-713 resistor changed (interrupted) | Substituir o r-713 100k | Paulo Sertel Itararé SP |
PHILCO | PCM2043 CPH05 | LED flashes (standby) and seconds after switching on | C-722 470x16 volts alterado | Replace it with a new one, if resolved | Paulo Sertel Itararé SP |