Philco TV Repair: Common Faults and Solutions.
Search: Philco
Results: 4740
Results: 4740
Philco Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
PHILCO | PH28S63 | Doesn't start. Stand by LED does not light up | Dead power supply | Capacitor c8->221x1kv , transistor q2->4n60, fuzivel f1 ->3,15a | oskarala |
PHILCO | PH650 | No sound/voltages ok | Headphone output board connector closing as if plug connected | Plate replacement or cleaning with contact cleaner | Renato |
PHILCO | PH21MSS | Frame reduced horizontally, more on the left side than on the right | After changing the power supply capacitors and resoldering on the board I found the r306, close to the vertical one, toasted, the value of 220r was replaced, the board was even reduced. I found a L458 coil without the ferrite magnet. was replaced and adjustments were made to the service mode | Mitzko eletronica | |
PHILCO | TP1454 | TV with normal sound and no color | Memory | After a reset the TV was normal | Eliel Magno |
PHILCO | PTV32E21DSWN VA | Image upside down after broken screen change. | Original screen t315xw03, replaced by hv320whb from a sony. | This model has several screen models in service mode, but the one I had installed was not on the list. This TV has 3 software versions. if it happens to you. check the lyrics after the series, if the | OLIBIO - ELETRÔNICA ESTUDIER |
PHILCO | PH32S61DG LED | Normal power supply, LED does not light | N804 fr9889 | Arimateia | |
PHILCO | PH40D10DSGW | Turns on, philco appears and turns off | 3.3v regulator, close to the selector, leaves 2v | Replace of the same | Rodrigo cofferi |
PHILCO | PH40U21DSGW | Turns off by itself after 20 seconds on. goes to standby. | Update software and reset via service mode. | rafaelmoraes99 | |
PHILCO | PH28D27D | The logo appears and the LEDs turn off, but the sound remains. | Defective LED bars, burned out or shorted LED. | Removing the 2r2 smd resistors (rb13, rb14) to lower the voltage on the leds to 29.2v the television will work normally. In my case, I only removed 1 rb13 resistor and it solved the problem. | JKSTek |
PHILCO | PH28D27D | Turns on the logo appears and turns off | Removing the 2r2 smd resistors (rb13, rb14) good luck | Removing the 2r2 smd resistors (rb13, rb14) good luck | JeanJKSTek |
PHILCO | PH32U20DSGW | Turning off | Software update | MasterCell Eletrônica | |
PHILCO | PH21MSS | The image appears and then turns off. the LED is blinking | Q201 c835 c847 e c826 | MARCONES DE ARARIPINA-PE | |
PHILCO | PH40E36DSGW | Heats up and turns off | Change without testing q8 | Comboer | |
PHILCO | PH14D | Doesn't start. | Q881 and d891 on the reference board is a diode. However, they add a resistor, in my case it burned out and I couldn't see the colors. Just put an in4148 diode in the right place. | Replace q881 2n5551 d891 (replace the resistor that replaces the diode) and place the diode in4148 | Nilmar |
PHILCO | PH40D10DSGW | Completely inoperative and without stand by | Motif u809 with a hole and c 997 shorted | Replace both | Cosme |
PHILCO | PHT660N2 | Totally inoperative power supply | Check open resistors r12 and r13 close to the ac input connector | Replacing the damaged resistors r12 and r13 | Jocimar |
PHILCO | PCX6000 CAIXA AMPLIFICADA | Doesn't start | Shorted mosfet transistor q16 | Replace and repair. | JC Eletrônica Cícero |
PHILCO | PH28N91D | Turns on with sound, weak backlight | Open led | Changing the bars | JC Eletrônica Cícero |
PHILCO | PH21 SS | 40% below without vertical image... that is, tsound was only 60% image | C563 and c562, then c406 | I replaced capacitors that supply the +15 and -15 (c563 and c562, even though the capacitance was not so out of the ordinary), and the vertical image opened, but tsound were small horizontal stripes at the top (5 or 6). Then I checked the generator signal (pin 3 of the vertical) and it was altered, I replaced it and the c406 image was perfect | David |
PHILCO | PH674 | Doesn't start | 5v pulsating power supply. | Tl431 | Baguatech |