Philco TV Repair: Common Faults and Solutions.
Search: Philco
Results: 4740
Results: 4740
Philco Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| PHILCO | PTV32G52S | With backlight but no image | Ao3401 shorted to position q1t on the main board and c153 shorted to t-con | Eletrônica Gero Som | |
| PHILCO | TP 2029 | Normal turns on characters appear, audio but no image and black screen | R723 4,7k smd aberto e c731smd com fuga | Replace the same | This email address is being protected from spambots. You need JavaScript enabled to view it. |
| PHILCO | PH20U21D | Shaky image | At v con withdraw the r99 good luck. | Eletrônica lelo | |
| PHILCO | PH40E36DSGW | Doesn't start | Power supply pulsing, front LED flashing | Shorted wifi board .shorted smd capacitor. | oskarala |
| PHILCO | PH32F33DG | The TV worked normally, after about twenty minutes the sound began to sizzle like AM radio waves. | 220mf/35v capacitor next to the audio IC, which had a low capacitance. | Replace the same. and run to the next repair. I hope I helped my friends. | Bruno Cardoso |
| PHILCO | PH32M | TV turns on normally....image...sound...characters (menu)......heats up for a few minutes and the image disappears and the sound remains (blacklite on)...change the channel and the image returns , repeating the defect | Are chap. ca08...ca12 and ca15....100mf / 16v | Alextecnico | |
| PHILCO | TPF2121 5502 | When turning on tsound was only audio, the +b had 30v. | 0 | To replace | Eletrônica Jordão |
| PHILCO | PH42F10DSGWAC | Reduce LED current | Remove rw53 3r9, rw52 1.2 rw54 1.2 and put one of 2r2, voltage drops from 95v to 79.5v | JR ELETRÔNICA & INFORMÁTICA | |
| PHILCO | PH32B51DSGWA LED | Reduce LED current | Remove rw819, rw821 and put a 2r2 one, voltage drops from 60v to 51v | JR ELETRÔNICA & INFORMÁTICA | |
| PHILCO | PH11000F | Totally dead | It is an 11 thousand btus portable air conditioner that has a recurring defect on the main board | Generally the problem is caused by the ci viper22 (u1) which burns in a short without blowing the fuse, in my case it burned several components on the board: one of the bridge diodes, the optical coupler (opt1), check the tl431 (u6), replace the schottky diode (d5) with another with a higher capacity (take it from an ATX power supply scrap), 47u 50v capacitor (e23) blown, 330u 25v capacitor (c3) bloated, check the 7805 (u7). | 2000 |
| PHILCO | TV PH21M SS SS | Pillow effect tv | D- 454 amended | Replace it for an equal or faster one as it is from a very fast circuit | ELETRONICA CAVALCANTE EM MARTINOPOLE |
| PHILCO | PH19R2 LCD (ROSA) CVMV26L-A | Red LED (stand-by) constantly access did not turn on via the control or button | Low voltage level in wakeup activation, low voltage level to release voltage for q9 and q3 | Replaced the two diodes (d1,d2) "m1" of the main one, replaced the 6 capacitors (16v/100μF) and the 2 capacitors (16v/470μF) | Elvis Cristiano |
| PHILCO | PH32E20DSGW | Tsound is a slight blink but no image appears | Change capacitors c1d3 c1d2 c1d4 c 180 c182 cob2 in my case good luck everyone | eletronica publison rn | |
| PHILCO | PH40D10DSGW LED | Does not tune channels | Power tuner with leakage (u001) with leakage between adj and out | Replace of the same | Rosmarino |
| PHILCO | PH32F33DG | Only flashes standby | Software on the pendrive! found sound on the website! software on the philco website, format the pendrive, insert the 2 files on the pendrive, unplug the TV, insert the pendrive into the TV's USB, turn on the TV with the power button pressed until the software installation menu appears, the TV will reboot and that's it. | Rogério Eletrônicoos | |
| PHILCO | 32F33DG | Standby LED blinks and back light does not come on | I downloaded the file sound, from electronica-pt and did the procedures via usb / power / socket, it worked | Rogério Eletrônicoos | |
| PHILCO | PH49F30DSGWA | The LEDs don't light up | Shorted diode vw9 | I replaced both vw9 and vw10 | jose ricardo cesila |
| PHILCO | PH42M2 | Sometimes it turns on, then it doesn't turn on again, sometimes it worked for 2 days and then it wouldn't turn on for days, | Q100 ci d13n3lt is what releases the voltages for the regulators +5v, 1v2, 3v3, 1v8 it also gives the defect of staying with 12v and 5v | guinga sdia goias | |
| PHILCO | PH32E31DG | Lights up, has sound but no image, heating up u3 a lot | C1n41 shorted, I'm next to the speaker connector | Replace this capacitor. | José Moura |
| PHILCO | PH20U21D | Does not turn on, does not light standby LED, 12 volt power supply shorted | Causa c801 smd | Changing the c801 0.1μF/50v from the 12volt line | MIGUELTV |