Philco TV Repair: Common Faults and Solutions.

Search: Philco
Results: 4740

Philco Repair Guide: Common Issues and Fixes

Brand	Model	Fault	Detailed Problem	Solution	By
PHILCO	PTV50G70SBLSG	Does not turn on or standby	Primary of the power supply with voltage and secondary with zero voltage, after disconnecting the 12v pci main connector present on the pci power supply, and short on the pci main	Replace 10μF smd ceramic that was shorted	Direto no defeito
PHILCO	TP2054	Sometimes it works and the brightness starts to blink causing these defects with low brightness and when turning on it appears as if it were out of horizontal and vertical frequency wanting to close at the top	Change zener zd 701 zener 8.2v 500mw changed		ricardovideoesom
PHILCO	PH32D LCD GH-MSD209GL-M1	No sound, low sound or noise. I verified that tsound was a lack of 5v on pin 8 of u52.	Cause: ca14 with leak (replace). see also r411		MAU3000
PHILCO	PH58E38DSG	STBY LED keeps oscillating between green and red	5volt power supply varying	Replace primary electrolytic capacitors c-41 4.7x50v c-29 4.7x50v c-70 22x50v c-36 2.2x250v c-33 10x50v	Alexandre-Minossi
PHILCO	PH19E	Doesn't start	Burned due to lightning discharge	It was necessary to replace the power supply board because it burned components that could not be recognized. Even after the replace, the TV did not turn on, analyzed the main board and found heating in the IC MP1482DS in position U1, on pin 1 voltage input of 5V and 3.3V did not come out on pin 3, replaced with another scrap and everything ok	Claudio Jorge Eckert Junior
PHILCO	PH58E38DSG	STBY LED keeps oscillating between green and red	5volt power supply varying	Replace primary electrolytic capacitors c-41 4.7x50v c-29 4.7x50v c-70 22x50v c-36 2.2x250v c-33 10x50v	Alexandre-Minossi
PHILCO	29PT5645/78	TV turns on, with black screen appears colored stripes and reduced frame	Electrolytic capacitor in position 2465 dry, just replace it and run for hug.		Seën store
PHILCO	PH39N91DSGWA	Without image, with sound. Dark screen, backlight off.	Burnt out bar LEDs. Philco ph39n91dsgwa television. without image, background shadow can be seen when external lighting is applied. burned out LEDs. replacement of all 40, for model 2835 3v. replacement of the (backlight voltage before 65 vc) rw 819 0r50 by 2r20 (current voltage 60 vc) to extend the useful life of the bus.		Giovani Pires Bitencourt
PHILCO	PME25	When opening the door, it activates the trio (bulb, mp and mv) at half power. If you try to heat food, only the magnetron is activated.	It was the main relay (the smallest) that was bad.		Chumbão
PHILCO	PTV43E60SN		Reduce current just remove the rb12 from 84v drops to 79v		naelson silva gravata pe
PHILCO	PH32B28DSGW	Turns on and off, locked restarts	Corrupt software, update via pendrive	On the philco website, enter the serial number and download the update, if you cannot download it through Chrome, use another browser that will close the window as soon as you click, but the download will be blocked, allow the download then	Mitzko eletronica
PHILCO	PH32E63D	TV inoperative power supply defect	Q201 k3673 with leak replaces with k6465d worked perfect in		Mijail eletrônica alternativa
PHILCO	PH32E63D	TV inoperative power supply defect	Q201 k3673 with leak replaces with k6465d worked perfect in		Mijail eletrônica alternativa
PHILCO	PH32 DTV	With sound and backlight. but no image. without the 12v that powers the t-com	Integrated u11	Just replace it	Paial.eletros
PHILCO	PH32 DTV	The backlight turns on and goes off in 2 seconds	Jp36 open	Just replace it	Paial.eletros
PHILCO	PH39N86DSG	Does not turn on or have stand by, power supplys half full	Change eb106	Run to the hug	M.Tristão
PHILCO	PH40U16DSG	No image, LEDs on black screen	Capacitor shorted on screen board cd6	Capacitor replaced	molina
PHILCO	PH21B PH08K_A. (VER:0,7)	Low power supplys +b giving 60v and very weak standby oscillating	C 523, just change everything solved		Jr eletrônica
PHILCO	PH55E51DSGW	The TV turns on, the LEDs turn on, tsound is no video, it seems like tsound is a defect in the main or display	As I have already obtained several tips on this site as well as on You Tube, I am passing this on to my professional colleagues: first check if tsound is a ci on the tcon with high heating, if so, turn off the flat in my case on the left side of the vcon then see if it has stopped the high heating in the ci, if so go to vcon and see the c107 smd in short it will solve it but it could be others that are on the same line in parallel, hugs.		Digitronica
PHILCO	PTV43E60SN	Beep in the audio after a while when connected and without an internet connection	Defective wifi card	Wifi card replacement	ELETRÔNICA POP TRON MAFRA SC.