Philco TV Repair: Common Faults and Solutions.
Search: Philco
Results: 4740
Results: 4740
Philco Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| PHILCO | TV PTV32G50SN | Does not turn on the LEDs.. | Defect in t con, when you turn it off, the LEDs come back on. | Na t con qe 10 and ct 843 shorted. | Eletrônica Lelo |
| PHILCO | TV PTV32G50SN | Does not turn on the LEDs.. | Defect in t con, when you turn it off, the LEDs come back on. | Na t con qe 10 ct 843 shorted. | Eletrônica Lelo |
| PHILCO | PH29E52DG | Dark image, not LED backlight | Low voltage in dc-dc inverter. 1m resistor rp70 giving 820k. just change. detail, in cp39 and 40 it has to give 45v. | Replace 1MΩ smd resistor position rp70. | NelsinhoPira |
| PHILCO | TV PH32E31DSGW LED | Doesn't start | 3 capacitors in positions c2d7/c1d9/e c2d6 | In my case I had to replace the 3 electrolytic capacitors position c2d7 /each and c2d6 | Airton Filgueira |
| PHILCO | PH29E52AG | Doesn't start | Burned fountain | Icp1 tea1733 , diodo zener zd205 18v . | TV TÉCNICA PARANA |
| PHILCO | PH48A12DSGWA PH50A17DSGWA PH55A17DSGWA PH55A17DSGWA PTV65A11DSGWA 4K | No sound or audio gaps | Cold solder on con21 headphone | Solve | BTAV_18-020 |
| PHILCO | PB330BT | Turns off by itself after a few minutes on | Resistor r217 of 10r / 56r of the ic4 3.3v regulator was hot. | Just replace r217 from 10r to 56r to lower the regulator input voltage. | Luciano Passos |
| PHILCO | PH28S63D | Turns on and then turns off | Auterated LEDs | Auterar r 119 for 4r7 | ALEXANDRE |
| PHILCO | PH32U20DG | Does not turn on standby LED on, difficulty turning on, power supply sound pulsing | Exhausted capacitor, position cp205 | Replace of the same resolved | Eletronica Valdecir |
| PHILCO | PH24B | Turning off a few seconds after turning on and the LED dims between red and orange. Sometimes it stays working normally for days. | Swollen power supply electrolytic capacitors and lots of cold welding | Capacitors c103, c104, c208, c209, c210, c211, c212, c213 were replaced and the soldering on the board was redone. | Pixel Assist |
| PHILCO | PH21M SS | LED off with a noise in the power supply like frying super heating the r319 and r320 | D815 | Replace without measuring the d815 1n4001 and just run for the hug. God be praised! | Sinailson furtado |
| PHILCO | PH58E51DSGW | Sem.image with blackilite | After changing the tcon, it almost condemned the display, the defect was in the main | Binho | |
| PHILCO | PH32M4 T051A | Doesn't start. | The TV displays 3v3 stb, when pressing power it activates 24v, but tsound is no voltage in the regulators on the main board, following the 24v sequence, I reached q100 (similar to an 8-pin memory), wsound 24v entered , but do not put voltage on any of the other pins. I just swapped it for one from another card and it worked 100%. | EC | |
| PHILCO | PH14D | The TV turns on with the LED blinking, tries to oscillate and the power supply voltage drops and the LED blinks again without stopping. | Tea2025b | Eliel Magno | |
| PHILCO | TP-2054 | 95v power supply does not arm, it is only at 20v, the stanbay LED is on, pressing the button does not turn it on. | Ci 102 faulty memory, test removes the gun power supply. | Replace of ci 102 memory. | guinga sdia goias |
| PHILCO | PH29 US A2 | Turning off after a few minutes | Transistor v574 open after heating up | Replace without measuring v574 | joão paulo sky |
| PHILCO | PH32E20DSGWA-VA ************** | TV lights up stand by LED and doesn't turn on | Capacitores: c2d2 - c2d3 - c2d9 3 eletrliticos = 100uf x 50v | Replaced resolved | FRANÇA-MACAIBA |
| PHILCO | PH28S86DG | The screen backlight does not turn on | Ok led, the screen doesn't light up, q19 is open on the signal board, replace it with an a19t, and run to the hug, defect resolved | robwood | |
| PHILCO | TC14A7 | Vertical 2 finger below reduced | R415 30k open | Replacement | eletronica tv som |
| PHILCO | PH32N62DGB | Sometimes it works and after a while the screen turns off as if it were the LEDs, a normal 12 and 5v power supply | Capacitor ec17 (100mf/100v) low capacitance | Replace and run to receive the farpel | Eletronica Maranata |