Sony TV Repair: Common Faults and Solutions.
Search: Sony
Results: 20067
Results: 20067
Sony Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
SONY | KV25XBR | No display | Two problems: 1) volume changes activate rgb mode. found rgbbutton jammed closed. 2) no channel/function display. found l101 on thea board to be open. there is 5v active low info. present at ic104/p12. | ||
SONY | KV2680R | No sound/pix, cold solder on 12v rectifier d-506 | This unit had no sound or picture. | ||
SONY | CFS88S | Audio from tape is distorted/low pitch | The motor was running about 25% too slow. | ||
SONY | KV2675R | Horiz output transistor runs hot, replaced t-501 | The horiz. output transistor ran hot on this unit. | ||
SONY | KV2680R | No audio, replace ic1107 and add capacitors/diode | The customer informed me that just before the sound went bad,they heard a loud snapping noise. i feel when the set is new and thetube snaps during its breaks in period, causes the ic1107 to become defec-tive. -hq comments: to protect ic1107 from static | ||
SONY | KV2141R | Horizontal frequency of - high pitched squeal, solder l801 | Horizontal frequency off produces high pitched squeal. | ||
SONY | D5 | Sled moving to outer edge upon power up | On power up sled moves to outer edge of disc. pin 68 tc201 isproper level. the only unusual signal is ic501 #23 which goes negative(5v). changed chips (ic801, ic501) no change. -hq comments: (found over the phone that disc did not rotate while sledmo | ||
SONY | TC44 | Part number needed | Need part number of gear (c) for tc-44. i have informed theservicer that the part may no longer be available. -hq comments: fortunately, the part is in stock at npc. part number is3-550-026-00. | ||
SONY | WMD6C | Motor does not turn | The customer told me that he plugged in 12vdc instead of 6v.the amplifier section was fine, but the motor did not turn. | ||
SONY | CFS300 | Part number incorrect - ic3 | On page 18 and again on page 20, ic3 is stated to be a la4126.on page 29 of the parts list, it is a la4125t. which is correct? theseare not listed in the handbook as being interchangeable. -hq comments: the correct part is la4125t. part # is 8-759-80 | ||
SONY | CCDV8 | Tape jam | Tape broken and wrapped around top of drum assembly. | ||
SONY | TCFX510R | Replacement of panel and buttons for rec and rec mute | Servicer would like to replace panel and buttons for rec andrec mute however, these buttons are not shown separately on page 35 ofs/m. can we get these or do we have to replace entire front panel assy? -hq comments: the rec and rec mute buttons are par | ||
SONY | BMC110 | Units dead | Units doa. after making basic tests, found pin 38 (reset)held at 205 volts. syscon ic301 not able to reset. located leaky capaci-tor c341. | ||
SONY | XR70 | Noise on the outputs in tape mode | Every xr-70 i have worked on has a motor noise in tape modethat is noticeable at low or no volume. -hq comments: head amp may be picking up motor noise as they are locatedclose to each other. try a shield around the motor. | ||
SONY | TCFX1010 | Communication with asp chip | Always in muted mode. tape plays, meters correct. in recordmode there is no control of level (rec) even though the attenuator reads-70db. ic710/703/704/309 replaced. all power supplies were within 0.3v. | ||
SONY | WM10RV | No auto stop | The unit did not stop or switch the direction automatically. | ||
SONY | WA16 | The unit changes direction fwd/rvs by itself | The unit changed the direction rwd/rvs by itself. alsonoticed the take-up and the supply reel did not turn. | ||
SONY | RS20 | No outgoing message | When we try to record the outgoing message, it rewindsadvances 33 reel count and seems to record the message. however, when wepush the in/out switch to out in order to monitor the recorded message,the unit makes the error beep. | ||
SONY | WA11 | No audio | There was no audio coming out from the speaker. | ||
SONY | RT44 | No play | The unit did not play tapes. the take-up reel did not turnand the head base did not go up. |