TV Repair: Common Faults and Solutions.
Search:
Results: 87427
Results: 87427
Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
SONY | ICF2001 | Repairability of units | Many units have been received with various problems, and dueto the nature of problems and product, have been unrepairable. requestsome form of product training, troubleshooting guide, and/or circuitdescriptions. -hq comments: training was given on this | ||
SONY | TAN77ES | Protection light on | Intermittent protect light. | ||
SONY | CDP110 | Inaccurate and missing procedure in section 2 of cdp110 s/m | 1. rf pll freq. adj.: serial/parallel tp must be graded forthis procedure to work. 2. no. 6 should read 4.2818mhz instead of4.3218mhz. -hq comments: you are correct. for future cases please refer to thecdp alignment manual that rick heal wrote. page | ||
SONY | KV20XBR | Intermittent | Very intermittent problem. at certain times, the sleep andrgb leds would light only and set would accept no other commands - alsodisplayed no sound or raster. i also noted the absence of high voltagewhen problem occurred. at the time of failure, inspe | ||
SONY | KV2680R | No system control, ic-1303 on "x' board | It was not possible to control any functions, picture andsound were muted. we found ic-1303 to be defective. pin 13 was constant-ly high and did not permit data out of the controller to pass. -hq comments: ic-1303 is quad nand gate associated with ic- | ||
SONY | KV1714 | Flyback | Flyback transformer part number 1-439-237-00 is substitutedwith part number 1-439-235-00. according to servicer, the substitute doesnot fit the pc board. -hq comments: flyback part number 1-439-237-00 had not been supplied tomass production. only seve | ||
SONY | XR7150 | Erratic function of tape mechanism | Unit will not load intermit., sometimes will not mute while inff/ams/rew, or when reversing tape will jam-reels turn but head & pinchroller do not move back into play. unit will jam and display e-99 error(mech.jam indication). touch/move head pcb-loadi | ||
SONY | D10 | Distorted audio | Distorted audio. | ||
SONY | KV27DS20 | Open speakers, replace sp | Both speakers open - everything checks good. the flexiblewire from the voice coil to the mounting post is broken. a set ofreplacement speakers was installed and within 30 days the same problemoccured. -hq comments: thank you for your report. | ||
SONY | WMF107 | Description for flex connectors | The service manual does not differentiate between the flexconnectors. they are all described as flexible pc board. | ||
SONY | XR7200 | Extension cables for servicing | Will a set of extension cables for servicing be made availablefor this unit? -hq comments: we have not been notified that extension cables will beavailable. i will ask tokyo and let you know. | ||
SONY | ITA600 | Unreliable 20 pps dialing | 20 pps dialing is unreliable. | ||
SONY | ITA500 | Unreliable 20 pps dialing | 20 pps dialing is unreliable. | ||
SONY | ITK500 | Unreliable 20 pps dialing | 20 pps dialing is unreliable. | ||
SONY | ITK300 | Unreliable 20 pps dialing | 20 pps dialing is unreliable. | ||
SONY | CCDSP7 | Owners manual correction | There is an error on page 70 of the ccd-sp7 owners manual.the directions for macro are to press the telephoto button all the waywhile pressing the macro button. actually, the wide angle button must bepressed instead of the telephoto. | ||
SONY | KPR46CX10 | No picture, replaced ic402 | No picture, high voltage ok, abl/protect circuit in protectmode. 12v on collector of q-4441. | ||
SONY | KV2649R | Remote control - turn on only all other functions inoperable | Remote control - turn on only all other functions inoperable.manual control on/off ok all other functions inoperable, plus unit waslock on one channel uhf-25. | ||
SONY | KV27SXR10 | Convergence problem, magnets added | When using cross-hatch pattern from ntsc generator, thebottom line looks like this plus top line is like this. | ||
SONY | XR6150 | Schematic error | Emitter at q513 is drawn in the schematic as being connectedto ground. on page 13 the emitter of q513 is actually connected to thenext line lower, the anode at d526 and one side of s902 mute switch. thepictorial view of the main board on page 11 and 13 |