TV Repair: Common Faults and Solutions.
Search:
Results: 87418
Results: 87418
Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
SONY | KV1354R | No programming, replaced q-024 | Unit would not hold memory. when you set tunning switch on vcwould go to max. and green tuning bar was all the way across. checkingaround memory chip ic-002/pin 2 had no -25v. found q024 open.also found that q-024 on some sets replaced with a 680Ω | ||
SONY | KV2670R | Intermittent audio, speaker lead cold solder | Two units with intermittent audio caused by unsolderedspeaker leads. | ||
SONY | SL2400 | Power supply | Unit will not cut off with power switch or remote. this unithas a ps-34 and ps-35 circuit board (power supply). it is not ul listed.how do we get the correct service manual? -hq comments: a supplement-2 was issued in jan 1984 which covers theps-34 and | ||
SONY | KV25XBR | Rgb goes on by itself | Rgb will turn on at sound vibration or by opening/closing ofcontrol panel. the unit sensitive to vibration has its rgb buttontouching the switch and just slight vibration will turn it down. | ||
SONY | PST20 | P/n for headshell | We need a p/n for the headshell of ps-t20. page 22 of themanual shows it but only gives p/n for cartridge. -hq comments: the p/n for the headshell is x-4857-616-0. it is listedon page 38 in the service manual (for us and other destinations). | ||
SONY | SLHF300 | No operation | Betamax would load cassette and tape. play button was pushed,nothing happened. tape could be unloaded. | ||
SONY | FH7 | Cable connector | Need a p/n for a connector on page 23. itunit (equalizer). the one on the left side of the pictorial is the onewith no p/n in the manual. the connector is a 5 pin. -hq comments: part numbers for the cord with connectors are:1-556-475-00 13p one end m | ||
SONY | KV1770R | Flyback arcing | The flyback burned a hole through the side and shorted outthe horiz. output transistor. | ||
SONY | KV1770R | H.v. shut down | The unit would go into hv shutdown at approx. 100v appliedac. found r559/hold down to be cold soldered. | ||
SONY | STRVX550 | Ic301 shut down | The oscillator on ic301 was not running. we found pin 34 tobe low. this was caused by ic401/p19 staying high. ic401/remote decoderwas defective. -hq comments: actual power on is equivalent to conventional units whenyou press system power. then the s | ||
SONY | STRVX550 | Dead - no display | No display. no clock signal at pins 31 or 32 of ic301. hold(pin 34) of ic301 at 2.5v. | ||
SONY | STRVX350 | No memory | Unit would not retain memory when powered off. hold line was7v instead of 4.9v at ic301 pin 34. found q803 leaky. | ||
SONY | KV25XBR | No display | Two problems: 1) volume changes activate rgb mode. found rgbbutton jammed closed. 2) no channel/function display. found l101 on thea board to be open. there is 5v active low info. present at ic104/p12. | ||
SONY | KV2680R | No sound/pix, cold solder on 12v rectifier d-506 | This unit had no sound or picture. | ||
SONY | CFS88S | Audio from tape is distorted/low pitch | The motor was running about 25% too slow. | ||
SONY | KV2675R | Horiz output transistor runs hot, replaced t-501 | The horiz. output transistor ran hot on this unit. | ||
SONY | KV2680R | No audio, replace ic1107 and add capacitors/diode | The customer informed me that just before the sound went bad,they heard a loud snapping noise. i feel when the set is new and thetube snaps during its breaks in period, causes the ic1107 to become defec-tive. -hq comments: to protect ic1107 from static | ||
SONY | KV2141R | Horizontal frequency of - high pitched squeal, solder l801 | Horizontal frequency off produces high pitched squeal. | ||
SONY | D5 | Sled moving to outer edge upon power up | On power up sled moves to outer edge of disc. pin 68 tc201 isproper level. the only unusual signal is ic501 #23 which goes negative(5v). changed chips (ic801, ic501) no change. -hq comments: (found over the phone that disc did not rotate while sledmo | ||
SONY | TC44 | Part number needed | Need part number of gear (c) for tc-44. i have informed theservicer that the part may no longer be available. -hq comments: fortunately, the part is in stock at npc. part number is3-550-026-00. |