TV Repair: Common Faults and Solutions.
Search:
Results: 87416
Results: 87416
Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
SONY | SPP11H | Open q4 | Noise from hand unit in talk mode even with base-unit powered. | ||
SONY | SPP11 | Defective ic2 ne567 | Base unit would not respond to any function from hand unit.in use light did not light, would not dial out. found ic2 pin 8 wouldnot go low. | ||
SONY | RT66 | Defective reel motor | This unit had poor ff/rew torque and would stall when using90 min tapes. | ||
SONY | RS30 | No shut off after the caller hung up | This unit would take one minute and sometimes more to shut offafter the caller hung up. there would be just a dial tone recorded on thetape. about every 15 seconds the unit would try to hang up. there wouldbe a click recorded on the tape but then the | ||
SONY | PSX55 | Broken contact on switch cam | The tonearm on this unit would not move in to the edge of therecord all the way or set down. we noticed a slight amount of friction inthe tonearm travel. disassembly revealed a broken contact on the switchcam (the electrical feeler that contacts the ca | ||
SONY | PS333 | Defective pitch control | Neither 33 or 45 rpm would lock in. speed was excessive.voltage were correct. | ||
SONY | PCMF1 | Defective d102 | Left channel was noisy - rec level control had minimal effecton noise - input signal was weak and distorted - line amp had some dcoffset at input to lpf - found constant current diode d102 breaking down.when testing this diode on a curve tracer using a 1 | ||
SONY | ICF9540W | Defective q1 | This unit had poor sensitivity and distorted output in thefm mode. we found the rf amp to be defective. | ||
SONY | CFM200 | Missing part number | The p/n for the mechanism chassis is missing from the servicemanual. however, the chassis from the cfs-400 appears to be very similar,this chassis is p/n a-3102-043-a. are these two chassis the same?the part for the cfm-200 was researched by kc with ne | ||
SONY | CDP101 | Unit out of adjustment | Unit would skip on 2nd track and 5th track. | ||
SONY | CDP101 | Would not read toc | Would not read toc. i could hear something rattling insideunit when i took it out of the box. i found one screw inside that shouldhave been in the sled motor bracket. after correcting this, it still didnot read disc. output of ic403 (eye pattern) was | ||
SONY | CDP101 | Stuck objective lens/coil assembly | The disc would eject before the toc could be read. focusdc drive out of ic204 (tp 10) was correct, but the objective lens in thetop was not moving. | ||
SONY | XR77 | Defective ry301 | The left channel would intermittently cut out on am/fmfunctions during first 5-10 minutes. this at first appeared to be causedby a defective semiconductor. further examination revealed relay 301 tobe the cause. heating and cooling the relay confirmed | ||
SONY | XR77 | Defective q105 | The left channel fluctuated between distorted low output andno output. we found q105 (muting transistor) leaky. | ||
SONY | XR70 | Error in manual | Terminal marking for q303 as shown on pc board incorrect(emitter and base leads reversed.) the picture on page 6 of the servicemanual (supplement #1) is correct but it does not match the silk screenon the pc board. | ||
SONY | WMD6 | Pinch roller support needed bending | C-90 tape (tdk) would not run properly through capstan andpinch roller. problem existed only on tdk 90 minute tapes. hi freq.would drop out-left channel would decrease in volume. tape wrinkleevident at capstan. pinch roller and capstan replacement do | ||
SONY | TCK777 | Poor chassis ground connection | Low level hum in output. | ||
SONY | TCK55 | Defective relay | Right channel meter erratically pegs accompanied by loud hum. | ||
SONY | TCK44 | Q310 shorted | This unit had a squeal in the left channel, about 5 khz, itfirst appeared to be a ground problem but closer examination revealedg106/q206 muting transistors to be partially turned on. | ||
SONY | TCFX500R | Bent tab on head chassis | Head deck would cycle up and down about 3 times after fwd button was pushed, then there would be a graunchy noise and deck would go into ff. |