PHILIPS TV Repair: Common Faults and Solutions.

Search: PHILIPS
Results: 14168

PHILIPS Repair Guide: Common Issues and Fixes

Brand	Model	Fault	Detailed Problem	Solution	By
PHILIPS	32PFL3403	TV completely inoperative	Jumper j14 match.	The cause of the j14 break was the 33μF/450 c910 with an electrolytic leak, which is why it is necessary to replace it even if it shows good on the capacimeter.	marco.32
PHILIPS	32PFL3403	TV won't turn on completely inoperative	Jumper j14 match.	Check bd2 if it is shorted, it is close to j14 and check r3. in my case I only replaced j14 which was broken.	marco.32
PHILIPS	32PFL3007D/78	Doesn't start (dead)	Shorted hdmi switch chip, in my case (sii9185actu) replace it and that's it it kills the 5vdc power supply		Edmundo
PHILIPS	20PT528A	Does not tune to all channels	Pin 9 of the seletronic has 10v when it should have 33v	Capacitor 47n 2004 smd, substituir	fabiosilvar
PHILIPS	42PFL3403	Doesn't start	It doesn't have 3.3v	Swap c120 semi shorted 103x2kv blue high voltage	jcgiantomaso
PHILIPS	21PT5433/78	Normal image after 5 minutes the sound arrived.	C-2444 seco total	Replace it for another like it	ELETRÔNICA CAVALCANTE MARTINÓPOLE-CE
PHILIPS	21PT5435/78	Turns on and off in 3 seconds	Shorted thermal controller, bc547	Replace components and adjustment of the screen and focus. normalized.	BICHARA
PHILIPS	21PT5433/78	It turned on normally but without an image with characters	R-3442 fully open. Sometimes you also need to change the c-2441	Replace and that's it!!!	ELETRÔNICA CAVALCANTE MARTINÓPOLE-CE
PHILIPS	FX30X/78	Does not turn on / inoperative	Touch switch on and off	Changing the on and off touch switch	JESUALDO / JM ELETRONICA
PHILIPS	FWM779	When connecting to power, the red LED lights up, the relay hits and then "everything dies", it does not accept any function, does not give power, does not light up the LED.	The defect is on pin 11 of the larger input transformer, which has poor invisible contact, due to the weight of the transformer, over time the solder cracks around the pin contour.	Poor contact pins of the larger 5900 transformer at the power supply.	MIGUELTV
PHILIPS	14PT 3131/78	Vertical closed clear line in the middle of the screen lights up and goes out without stopping	Broken track 160v	Scrape and redo the trail	ELETRONICA OURICURI
PHILIPS	29PT	Yellow image	Cold solder on the board		Eletrônica datacheet
PHILIPS	15PF9936 17PF9945 23PF9945	TV doesn't start, red LED is on but doesn't turn on	Ver resistores 68r/5w psu	Replace for 68r/10w	Mário Martins
PHILIPS	42PFL3403	Doesn't work, power supply doesn't start	Diodo smd zd103(20v), u101(fsq510)		Mário Martins
PHILIPS	14PT110 14PT112 14PT220A	Half screen and with characters stacked from top to bottom	Change without testing vertical ci tda3653	Closed from the right to the middle of the screen, normal sound, on the left side a good image and only characters appear when the TV is turned on. The channel number appears stacked from bottom to top. After leaving the channel number, tsound are no more characters such as menu, brightness, etc. You can't even enter service mode as it doesn't appear on the screen. It is unimaginable to think that the vertical ci could cause such a defect. replace tda3653 without testing, put new one.	cesar
PHILIPS	14PT110	Half screen and with characters stacked from top to bottom	1st change tda8360 and if that doesn't work, change it without testing vertical ci tda 3653		cesar
PHILIPS	14PT110	Half screen and with characters stacked from top to bottom	Change without testing vertical ci tda 3653		cesar
PHILIPS	40PFL3805D/78	TV completely inoperative	C502 on the power supply board shorted (100pf/1kv)	Replace the same	Deivid Vanzuita
PHILIPS	FWM208/55	Locks functions/slow and does not tune	Crystal with corrosive glue and washing the PCI under the CD		Ângelo MG
PHILIPS	42PFG6809/78	Doesn't start	Power outage		Jefferson