PHILIPS TV Repair: Common Faults and Solutions.
Search: PHILIPS
Results: 14168
Results: 14168
PHILIPS Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
PHILIPS | 42PFL3508G | Doesn't start | Capacitor c9169 | Tec Center | |
PHILIPS | FWM2200X/78 | Low clicks in the boxes, | Change 50v 1000uf capacitor, close to the box connectors | Ronaldo bylu | |
PHILIPS | 42PFL3604 | Doesn't start | No standby voltage, LED off, no signal | Check the primary coil (in my case it was broken), replace the 4.7μF x 450 v capacitor, it was swollen. After replacement it started working again! | Augusto Azeredo |
PHILIPS | 32PFL5607D/78 | It doesn't turn on, it just stays on standby, the LED lights up white and goes to red | Normal power supply voltages, grounded stand by pin, black light comes on and generates all voltages | I did a reset, holding volume + and the arrow key (input) while plugging it into the socket, it worked normally after that. | ser-mga |
PHILIPS | FWM416/78 | Shows disc reset fall when inserting the usb pen driver | Lack of reset on the CD due to lack of power | Causes capacitor 168 to short on the 8v line. After changing the capacitor, the 8v came back and the device rang normally | |
PHILIPS | 40PFL9605D ? | The TV turns on, the image appears and then it turns off, only the sound remains. | Guys, the cause is q702 and q703, these two transistors are responsible for the switching of the transformer that feeds the 185 volts to the LED bars, I replaced the two fets and everything was resolved. | Replace the two fets q702 and q703 that were leaking and everything is resolved, let's stop being selfish and help others. | <small>This email address is being protected from spambots. You need JavaScript enabled to view it.</small> |
SOM PHILIPS | FWM210 | Display does not show characters | After evaluating the board, I noticed that tsound was no 10 volts (I put a 560 omhs resistor on the r524 that tsound was no board and the sound started working again | eletronica max es | |
PHILIPS | 14PT414A | Does not turn on, power supply less than 20v | C2540 100µ 25v | Changing the c2540 close to the power supply trimpot | Marcelo Piranga |
PHILIPS | FX30X/78 FX30 | Doesn't start | N channel mosfet (q13) does not switch the +5va to the panel. | Replace the component. | barcelos32 |
PHILIPS | 32PFL3008 | Dead | C709 smd na pci main | I took it out | Adrian Chapadão do Céu Goiás |
PHILIPS | 40PFG6110 TV 715G6677-P02-001-002H | Did not turn on inoperative | Power outage | Smd diode d9311 short swap | Júnior eletrônica |
PHILIPS | 32PFL5604 | In my case the defect was in c120, on the screen board. dismantle the screen to gain access. replace c 120, short. | Check "t-com" board voltage at c60,61= 0v, it must be 26v. see c110,115=0v, it has to be 16v. | In my case the defect was in c120, on the screen board. dismantle the screen to gain access. replace c 120, short. | arock |
PHILIPS | 32PFL3404 | Turns on and after a while it turns off or the relay keeps hitting | Troque na placa principal.. c474, c532, c534 | C474, c532, c534 | José Oscar da Silva |
PHILIPS | 32PFL3404 | TV turns on and off or the relay keeps hitting.. | C474 defect on main board | Replace c474 na 4.7 aluminum main plate.. | José Oscar da Silva |
PHILIPS | 39PFL4707G | Nothing turns on, not even the STB LED | Voltage of 5v with approximately 2.5v | Replace the power supply capacitors on the 5v line | |
PHILIPS | NTRX700 | Very low sound | R 304 100r burned and diode d303 shorted | Just replace and run to the crowd | Wenceslau |
PHILIPS | 32PFL3008D/78 | The LEDs turned on and off. | I changed the memory and it was upside down. | I solved it with code. 062598 + little house + 002 I will deliver to the customer | PIG QUILES |
PHILIPS | 32PFL4606 | Does not turn on intermittent | Cold welding trafo power supply | Gilmar L. | |
PHILIPS | 40PFG4109 | With sound without image | With sound without image and LED on, check c06,c08,07 on the screen board next to the diode | Cabeça | |
PHILIPS | 42PFL3604 | Does not generate 3.3v | Burned fountain | Replace without measuring, u801 ci fs510 / d813 her108 / d809 sr160 / os photo u802 and u804 / r825 put 4r7 up to trafo /c806 4.7 x 450v | JORGETVPARANA |