PHILIPS TV Repair: Common Faults and Solutions.
Search: PHILIPS
Results: 14168
Results: 14168
PHILIPS Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| PHILIPS | FWM998 E317642 R:1.3 | No audio comes out of the outputs | R12 open or altered this faulty resistor raises the +b above 41v the tda8954 supports up to 41v above that it goes into protection | Marcelo | |
| PHILIPS | 14PT3336/78 | Black band at the bottom of the screen | C 2428 of 47uf /16 v | Replace | Eletrônica Mauro Mascarenha - Parazinho Ceara - Tel : (88)981422821 |
| PHILIPS | 43PFG5000 | No image with sound and backlight on | I saw some tips sound on the forum and most of them said it was the c216. I looked on the ruler on the right side with the TV lying on the counter and I couldn't find it, I just found the c218 and when I removed it I found the short | To find out if the defect is in the t-con or the tele board, you must first check the voltages on the t-con board, vcc vgh and the others, close to the flat on the right side, if it is zero, remove the cables and take the measurements that will appear because this shorted capacitor was killing the t-con voltage | marco.320 |
| PHILIPS | 20PT3331N/78R L03.1L AA | The TV has a normal image, but the sound is very low on the speaker... | The diode was removed: 6908 (zener smd bzx384-c2v7), and replaced, the c2444 had a low esr, after the change the TV came back with normal sound | ... then it was just a matter of hugging!!! | ENDEL NEIVA |
| PHILIPS | 42PFL3507D | With sound but without image | Capacitor in t-con position (c209) and t-con fuse (f1) | Mario Moreci | |
| PHILIPS | 220TS2L | When I activate power, it turns on standby and then goes out. | Cause: c910 1000µf/10v on the power supply board, near the output harness | Lucas | |
| PHILIPS | FWM653 | I'm sound | Does not arm the amplifier power relay | D904 shorted | DiegoDLA |
| PHILIPS | 21PD5932 | Doesn't read dvds | Optical drive | In this case, it uses the SFHD 60 but you can use the SFHD62 | DR.Luan Vintage |
| PHILIPS | 21PD5932 | Takes time to load dvd | Check capacitors on the dvd power supply board and the main | In my case it was the capacitors on the main board that were all dry. | DR.Luan Vintage |
| PHILIPS | 20GL1045 20 | TV with sound and no image | Open 2010 capacitor and cold solder. | Replace the 2010 25v 100μF capacitor and resolder the board. | Trafo elêtronica São Geraldo MG |
| PHILIPS | 42PF9945 | Power LED (red) lights up but does not turn green, the TV does not turn on. | Check the two 68r/5w resistors in the power supply | Mário Martins | |
| PHILIPS | 40PUG6300/78 | Dead doesn't start at all | Short smd diode | Replace shorted diode on the q9303 line | Vital eletrônica Hawaii 12 |
| PHILIPS | 14PT314A/78R | When changing the fly_back the TV worked normally but after a few minutes it started to turn off intermittently and also when pressing the volume key the TV entered the menu | Q7611 | Just make a jump on the base and collector of the 7611 smd transistor and the TV will work normally. Praise be to God! | Sinailson furtado |
| PHILIPS | 14PT314/78 | When plugging the TV into the socket, the stand bay light no longer turns on. The TV in the armpit generates a very weak high voltage. When adjusting the screen to the maximum point, a horizontal line appears at the bottom of the screen. | C2551 and c2409 | Replace without measuring the c2551 is the c2409 of 47μF160v and that's it, the TV will work normally. | Sinailson furtado |
| PHILIPS | NTRX500 NTRX700 NX5 NX7 | Blinking LEDs wouldn't turn on | Change the 5 electrolytic capacitors around the ci smd u501 on the panel board, 1 capacitor 100/10v+4 47uf be careful because the tracks break in the solder they are very thin | eletronica junior reginaldo moronte | |
| PHILIPS | 29PT9467 | Cushion effect | Q440 (irf630) shorted and 6.8r region 440 open | Replace both | Laercio |
| PHILIPS | 32PHG410978 | League has sound but no image | After checking everything and thinking it could be the negative led bars | The problem was with the output of the black lights socket, it was the IC that triggers the LEDs in shorts, it is close to the connector and it is the only one with 3 large legs on the power supply board and just replace it and go to dim dim | ELETRONICA PUBLISOM DE NATAL RGN |
| PHILIPS | 48PFG6110/78 | Doesn't start | Short cut fast smd diode | The replace of the same | Airton Filgueira |
| PHILIPS | 21PT9467 | Turning off after turning on | Defective computer | Sorry, the way to place the diode in the previous post is wrong, correcting it, placing the diode in4007 anode pin 36 cathode to ground, it will keep pin 36 at 0.7 volts and it will no longer turn off | HP ELETRONICA |
| PHILIPS | 21PT9467 | Turning off after turning on | Defective computer | Place diode 1n4007 cathode pin 36 anode on ground, it will keep pin 36 at 0.7 volts and it will no longer turn off | HP ELETRONICA |