PHILIPS TV Repair: Common Faults and Solutions.
Search: PHILIPS
Results: 14170
Results: 14170
PHILIPS Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| PHILIPS | GR6/AL/GR6LS | Does not work LED blinks 2 times | Ts 7500 (ts driver horizontal) | ||
| PHILIPS | GR6/AL/GR6LS | No image with/sound | EEPROM data loss. exchange it | ||
| PHILIPS | GR6/AL/GR6LS | No image with/sound | Ic 7855 (vertical) | ||
| PHILIPS | GR6/AL/GR6LS | No image with/sound | C-2573 (contrast) | ||
| PHILIPS | GR6/AL/GR6LS | No image with/sound | C-2226 (100k) | ||
| PHILIPS | TV PROCESSADA | Gl,cn models | First step, if the device is turned off, you must turn off the resistance that controls the power supply in the case and a resistance of 4.7k (r-3924) (processor reset resistance). If the device does not turn on, the defect is in the power supply. and if you turn it on, the defect is in the processor. defect in the power supply: it could be an open electrolytic capacitor, diode transistor or the protection SCR. processor: it could be the processor itself, but first you must check the 5 volt power supply, the e-eprom (memory integrated circuit) or the sand-castle pulse or the vertical integrated circuit as there is an operational amplifier working inside it with the sand-castle wrist. If you change the e-eprom you must program the new one as it is not programmed. see item adjusting an eprom on a phillps television when changing the e-eprom nothing will appear on the device screen it will only light up the tube filament to see anything you must increase the voltage on the tube screen grid a little. | ||
| PHILIPS | CN | Every time you turn on the TV or change channels, the sound takes about 5 to 8 seconds to appear. | This involves changing the electrolytic capacitor in the remote control receiver box, opening the shield and putting it back. | ||
| PHILIPS | 20CT6255M | The sizzling sound | Coil s-159 defective tubular capacitor | ||
| PHILIPS | 20PT-324A | TV has sound and no image works for 8 seconds and turns off, stays on stand by, | Defective flyback | ||
| PHILIPS | 16CN-4036 | Does not tune channels only drizzle. | 4r7 resistor is close to the channel selector or the capacitors c-111,c-112, c-113 are shorted. | ||
| PHILIPS | 16CN-4036 | Defect warping the image and losing synchronization. | Causes electrolytic capacitors connected to the ci 2577, replace them all, including those on the 12v power supply. | ||
| PHILIPS | 16CN-4036 | Stop | Normal power supply filament lit r-404 open. | ||
| PHILIPS | 20PT-120A/78R | Vertical with noise at the top of the screen. | Resistance r-3407 of 220Ω open. | ||
| PHILIPS | 20PT-122A/78R | Defect TV doesn't turn on, stays on stand by. If you press the channel key it turns on, but if you release it it goes back to stand by | Shorted 6650 9.1v zener diode is close to the micro. | ||
| PHILIPS | CN-4037 | Retraces on screen | C-400 (100 µf 25 v) | ||
| PHILIPS | 29 VáRIOS MODELOS | Defect direct linked demo characters. | Solution press volume - and channel + at the same time and it's ready to unlock. | ||
| PHILIPS | 14GL-1316 | Defect did not tune. normal tuning voltage and normal screen characters. | T-7100 defect band switching. | ||
| PHILIPS | BP BL2002 | Strong ripples in the video. | The cause was changing the buk444 mosfet which resolved the defect. | ||
| PHILIPS | 20GL1040 | Completely inoperative or acting protection. | Causes c-508 680pf-3kv with internal sparking. | ||
| PHILIPS | 12BX-BP | Horizontal outlet overheats and burns. | Causes drive transformer, replace or place a 100kpf polyester capacitor between pins 2 and 1 of the drive transformer, this will solve the problem. |