PHILIPS TV Repair: Common Faults and Solutions.
Search: PHILIPS
Results: 14168
Results: 14168
PHILIPS Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| PHILIPS | 52PFL8605 | I retightened them all and it started working normally again. | I found all the internal screws loose, loose. | I retightened them all and it started working normally again. | arock |
| PHILIPS | 32PFL5606D | Does not turn on or turn on standby | This is a processor initialization problem (Hercules) | This is a processor initialization problem (hercules), I turned off the device, disconnected the touch keyboard and remocon cable and reconnected the device with this connector disconnected, if it turns on normally, reconnect the connector with the device turned off (of course) and plugged it in again | Emerson |
| PHILIPS | 32PFL3404/78 | Turns on, everything is normal, after a while on, video disappears, sound remains, lamps on. | Capacitors c532, 534, 526,528, 529. | Replace them all, everything goes back to normal. | arock |
| PHILIPS | 40PFL9605D/78 Q551.1L MONET | Disappears image, flashes image, and turns off with LED flashing 9 times. | On the t-con board, check the 15v supply. tsound is a ci position switch fet1102 that stops working and does not release the 15v forward. | Replace the component, or place a 1r x 1/4 resistor in place of the switching ci. | Rafael do Carmo |
| PHILIPS | FX50X/78 | Turns on, the LEDs that illuminate the panel light up but the display does not light up and no function works, because tsound is a lack of 12v that goes to the front panel | Diode d7, smd diode (in the body of the diode is s8) on the amplifier board, circuit that makes 12v that goes to the front panel | Replacing the s7 diode with a normal her105 diode. | MIGUELTV |
| PHILIPS | 29PT5642 L0.4 | Cup effect | L5403 coil with loose island | Retrace the coil tracks with thread | Bardock Eletronica |
| PHILIPS | 29PT5642 L0.4 | Vertical only opened from the middle down | After breaking the head, I changed capacitors, tested with another deflector, I re-recorded the eeprom, looked at resistors and diodes, but when I moved the board, the vertical one opened, I saw with a magnifying glass it had a small crack and even testing continuity with r3465 and c2463, it was good, so I made one wired jamp the tv was cool | Make a jamp with wire from c2463 to r3465 this model usually gives problems with trails | Bardock Eletronica |
| PHILIPS | FWM208/55 | Doesn't work | No 3.3v voltage on the micro | Replace of 3.3v ic 1117-33 next to ic 103 | DiegoFly |
| PHILIPS | PT3436/78 | No image but with characters | R3442 150k | Ok | video som |
| PHILIPS | 21TP5435/78 | Black stripe on the left side of the screen | Memory | Replace | Eletronica Mauro Mascarenha. Parazinho - Ce Tel : (88) 981422821 |
| PHILIPS | 21TP5435/78 | No audio and when you turn on the TV it goes into service mode | Microprocessor | Replace | Eletronica Mauro Mascarenha. Parazinho Ceara Tel : 88981422821 |
| PHILIPS | 21TP5435 | When turning on the TV, it enters service mode with a normal image without audio | Microprocessor | Replace | Eletronica Mauro Mascarenha Tel : 88981422821 |
| PHILIPS | 29PT9457/78 | Does not turn on, LED takes a while to light up and pulses | Photocoupler | I replaced the TV, it turned on | Lucafer |
| PHILIPS | 20PT324 | Lines retracing in the middle of the image, tending to close the vertical | C2409 (47x250v) | HP ELETRONICA | |
| PHILIPS | DVP3120 | It wouldn't open the disk access cover or turn on or give any signal | After testing the power supply, a short was found in the controller; faults were found in the power and open/close buttons on the deck and the rubber that moves the disc tray was broken. | Replaced everything and it works perfect again! | Jailson Lima |
| PHILIPS | 32PFL3403 | TV in AV, blue screen, keyboard blocked. When turned on, it immediately turns off. | Remove c2p10, 10 mf ceramic. It is next to the sensor and has no identification on the PCI. This capacitor will be leaking, killing the 3.3v from the remote control receiver. | Remove the capacitor, | aladim |
| PHILIPS | 48PFG6110 | Directly replace the 9311 diode | Raul de saja eletronica R.E | ||
| PHILIPS | 29PT4635 | LED lights up, turns off using the control but does not oscillate on stand by 95v and on 140v | 7460 changed | Put bu4508 | samuel leite |
| PHILIPS | 20GL1049 GR1-R03 09 | TV does not turn on and the LED is off, but tsound is a starting signal from the power supply. | The c2346 and c2347 were found dry (without capacitance) and, after changing them and carrying out a general inspection of other components, the TV was connected to the network and everything was ok. | Luiz Cassiano de Carvalho | |
| PHILIPS | 42PFL3607D | No image on screen lamps on! no 12v on t-con | Bad q400 small ci at the bottom of the board with 8pins | I couldn't read the number but I took it from a similar plate!! | orlando lott |