Search: PHILIPS
Results: 14169

PHILIPS Repair Guide: Common Issues and Fixes

Brand Model Fault Detailed Problem Solution By
PHILIPS 1414PT3336
L 03.6L CA
Vertical closed, pulsing and turns off shortly afterZener (33 v ) next to varicap position 6001Resolved, thank you to all forum participants.geremias
PHILIPS20PT122A
L7L
When turning on the device, it showed the service mode activated, the LED responded to the remote control but did not turn off, suspending pin 8 of the memory turned it off and on normally.Cause: faulty memory (24w04)Replace itThis email address is being protected from spambots. You need JavaScript enabled to view it.
PHILIPS21PT5433
21PT5433
180v power supplyR3442ReplacementBento
PHILIPS14PT4131
Turns on and then turns off... sometimes it turns on again but turns off againDefective photocoupler... use and replace 2521 and 2528 (both 22u/50v)Eletronica Staub
PHILIPS14 PT 414
Turns on and off, when you keep the volume pressed it stays on, if you release it it turns offSee r 3440 amendedMaster Eletronica
PHILIPSPHILIPS
29PT8457/78
It gives a caption on the screen 00510l0453.4 err1951000 op000037128164250042008 (sdm)The power went out and this caption looked like this when the TV was turned onThis email address is being protected from spambots. You need JavaScript enabled to view it.
PHILIPS14GL1013 14GL1014 14GL1313 14GL1314 16GL1033 16GL1034 20GL1043 20GL2044 20GL1343 20GL1344_EE
70v low power supply +b with 37v replaced f422, f423, un4436Doesn't even turn on the stand byIt was only resolved by changing the tmp47c834n-r167 processor, the final letters must be the originalginaldo silva casa do radio picui para + dicas especificas na página principal do google casa do radio picui pb
PHILIPS20GL1343
GR1-L1
Normal audio without image when opening the screen is retraced and very faded.Video does not work. dead rgbCapacitor c3410 in the vertical sector completely depleted. replace and run for the hug.altair santos
PHILIPS14PT314A
The TV turns on, the screen appears with retractions and then turns off.The cause was broken resistor 3334=18k and capacitors 2409=47mf160v-2551=47mf 160v, I replaced them and the TV worked normally again.ELETRÔNICA MELO BOA VIAGEM -CEARA
PHILIPS42PF7320
Turning off with/shortlyChange the value of the 8094 resistor from 900k to 1m and adjust ve and vs, the voltages are at the top of the displayThis email address is being protected from spambots. You need JavaScript enabled to view it.
PHILIPS29PT 5645
Cushion effect, not acting (eww) -(ewp) - (ewt) for adjustments.Change the smd transistor (7484) bc 847. bc 547 can be usedAdemar Videira SC
PHILIPS21PT6456
Doesn't workSupply smd integrated circuitTea1506tEletronica lelo
PHILIPS21PT6456
Everything normal but no audioC2444 secReplace and run for the hugdigital system
PHILIPS29PT558
Doesn't startCapacitorc2450 47x160v l 5561 c2455 47x25v q337 q327Replace -thetoninho da eletronica
PHILIPS29PT5645/78
L04L AA
Image interference, only in rfWhen changing channels, interference from another channel comes inReplace in sam mode in tuner the parameters ifpll = 36, agc = 30 and cl = 10leitemarcellus
PHILIPS29PT4631
Warming up. 3343 on the rgb board...Flay-back jf0501-8604, it was not original. Just click a good...ELETRONICA INFOAÇU
PHILIPS29PT4631
Does not turn on, LED off + b normalCap. c2561Tip I got from a colleague on this forumELETRONICA INFOAÇU
PHILIPSFWM417X/78
DeadDefective 835 diodeReplace without measuringBOMTEMPOMECATRONIC
PHILIPS21PT5433
Without video and with retrace lines.Burnout of the screem return power supply resistors. r3441 and r3442Replace of the same - note: r3441 smd pin 10 of the three horizontal output - values ​​120kGiovanni George de paula
PHILIPS21PT8467/78
This TV turned on and off in 7 seconds and then it made a huge noise and then turned offI tested the transistors on the kinescope board and it didn't solve anything, I measured everything, everything was fine.Hold down the channel button + pressing for about 5 m and like magic it solves it..., this is incrediblemarcos informaticas