Philco TV Repair: Common Faults and Solutions.
Search: Philco
Results: 4740
Results: 4740
Philco Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
PHILCO | SS M 21 | TV without sound // don't play memory but new proven tip go to service mode 9735 and enter hotel-o=btsco-auto1= and that's it= ok, fine. | Total in sound | It is necessary not to touch the memory | luiztvsom |
PHILCO | PCM1446 | Does not turn on stand-by LED off | R 902 of 470k in primary power supply | Replace of the same | AssisTec |
PHILCO | PH650 | Dimmed display (off)....sound does not come out of the speakers. | Q205(8550) | I put it to work in its place bf423 (it doesn't heat up)...be careful the polarity of the legs are reversed!..º¿º´..hehe! | Alextecnico |
PHILCO | PH 21 USA1 | Vertical closed | Stv 8175a | I just replaced it with stv 9302a | josivete tavares afonso bezerra rn |
PHILCO | PH24M LED A2 | It doesn't turn on, it doesn't have 12 v, the primary power supply doesn't work. it only has approximately 158 v in q1 (7n60) | Z1 shorted (smd y8w33 zener 22v), photo p1(817) with leak, if it doesn't work, replace ic1(mjp 31) | If you don't have the SMD zener, put 2 11v in series. the ic that generates the pwm mjp 31 = ld 7531 = ku1 31a. The scheme I got was different. Good luck. | Oséias |
PHILCO | PH24M LED A2 | It doesn't turn on, it doesn't have 12 v, the primary power supply doesn't work. it only has approximately 158 v in q1 (7n60) | Z1 shorted (smd y8w33 22v zener. You can put 2 common 11v zeners in series if you don't have the smd), | Oséias | |
PHILCO | PH24B | Triplicate image, several images. | Memory with corrupted data. | Erase the data from memory, you don't even need to rewrite it, just delete it, leaving all the bytes with the value "ff". | Capiroto |
PHILCO | PH42M LCD | Losing audio | Remove the r199 and replace the 2 speakers | Go for the hug!! | MEDEIROS/ BARBACENA-MG |
PHILCO | PH 21 SS | The LED is on, the voltage is normal but it doesn't turn on after hitting the head I found the W405 and it's a jamp close to the horizontal transformer | W405 | Exchanging it and running for the hug | Eletrônica Carlos Viseu Pará |
PHILCO | PCS2976S | The TV turns on normally, with sound and image, and everything is fine, but after a good while on it turns off | The image and only the sound remains and the screen is dark. | Cold solder on the plate on the connections of that flat cable that carries the RGB signal plus the voltage of the kinescope filament | Armando de Olímpia |
PHILCO | PH21M SS | Turns on, image appears then turns off, LED blinking | Capacitor c833 and q802 with leakage 2n5551 replace. | Valdenio Marcelo | |
PHILCO | PH21MSS | TV arrived at the workshop without sound | After combing through the audio area without detecting anything wrong, I decided to rewrite the eeprom and it worked | I re-recorded the eeprom with data downloaded sound from the website and the TV started talking again. | opinioncs |
PHILCO | PH21MSS | Does not turn on low power supply blinking LED | After going through the power supply with a fine tooth comb, I accidentally found a shorted diode after the flyback | D455 shorted killing +b | opinioncs |
PHILCO | TP-2054 | No image does not memorize channels or brightness and contrast and vertical in half | Memory or capacitors | Replace or remove cpacitorea c118 and c119 near the memory | eletronica fernandes - to |
PHILCO | PH450 | Plays CD and USB in minutes and stops playing. radio works normally | 16v 47µf stoved capacitor (tc6) | Replace | Ronaldo bylu |
PHILCO | PH24D21DM | Turns on image appears and returns to stand by | Update | INTERTEC ELETRONICA | |
PHILCO | TP-2052N | TV turns on with retrace or return line and then turns off. r711 burning. | Change 4r7 resistor r711 and 471 capacitor c803 on the tube plate. 180 volt line. | Santim | |
PHILCO | TP14U56 | Does not turn on, nor does the stand-by LED light up | R 909 680k open | Replace for new | Eletronica_Almiro |
PHILCO | PH21C | Working but with image shaking power supply varying, noise in the power supply | D819 and q802 replace without measuring, 1n4148 and 2sc1815y | Dj Velk | |
PHILCO | PMS24 | With the door open, turn on the lamp and turn the plate, relay is ok | Small leak in the switching transistor | Replace transistor q7 near the micro 2sa1015 on the top of the board | BRUNO DOS SANTOS ALVES |