Philco TV Repair: Common Faults and Solutions.
Search: Philco
Results: 4758
Results: 4758
Philco Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| PHILCO | PH24D12D LED | Red LED stuck, won't turn on | Solution, rewriting or changing the memory. | carlossbs | |
| PHILCO | PH200 | The volume button only lights up but the sound comes out | L50 open hidden under burnt glue, power supply to the -24 on the display | manin | |
| PHILCO | PH21MGSS | Image with stripes | Changing the vertical IC and resistor r306 270r | MARCONES DE ARARIPINA-PE | |
| PHILCO | PH21MGSS | Image with stripes | Changing the vertical IC and resistor r306 100r | MARCONES DE ARARIPINA-PE | |
| PHILCO | PH32E53G | Inverted negative image after changing the main board | Configure fitury project data | With the TV on, type 062598 menu 013 after typing the TV turns off by itself when you turn it back on, everything will be ok | charlotniu |
| PHILCO | PH39U21DSGM | Turns on and after about 30 seconds turns off | Capacitores 120uf 400v, 68uf 100v | Replace the capacitors (120μF 400v this one and sound one) (68μF 100v these are two) note: in the off-board test they behave as if it were good but they are not making the power supply turn off | Charles nazareno Oliveira |
| PHILCO | PCM-2046 | Standby LED on, does not start | X 101 defective, replaced it and it turned on normally | Leandro | |
| PHILCO | PH24D21D | Red LED stand-by, does not turn on | Corrupted eprom memory | Rewrite eprom memory | Eletronica Jambeiro |
| PHILCO | PH200N | Turns on the blue volume LED lights up, but the display does not turn off | On the front panel board the c11-104 =100k 50v ceramic short I replaced, which caused the short comes to the main board, very close to the photocoupler the 2 resistor changed and opened r152-330r smd and r153-2k2 smd, already on pin d14 - fr107, tsound is an open resistor r137 - 2r2 smd and q17 - mpsa92 in short, near this transistor r139 - 100r with smd leak, I replaced these components and the display started working again | Defect resolved | Eletronica Hally |
| PHILCO | PCM-1451 | Then turns off. | Zd941 (30v zener diode) in the protection line. | To disarm the protection, simply ground pin 35 of the micro (ic101). | Noca (Manoel) |
| PHILCO | PCM-2051 | Then turns off. | Zd941 (30v zener diode) in the protection line. | To disarm the protection, simply ground pin 35 of the micro (ic101). | Noca (Manoel) |
| PHILCO | PH21MG SS | 3 colored lines at the top | Electrolytic capacitor c307 100uf 35v open | Reginaldo Alves | |
| PHILCO | PH21MMS | Turn on and off | Check q802 2n5551=mpsa42 check short q451 and c452 if they are good to change d 454 | Replace d 454 short | Center som |
| PHILCO | PB120N | USB doesn't work | Touch key (stop) on the function panel | For this device to work with USB, you need to press the stop key on the function panel so that it switches from CD to USB function and it did not do this operation because the key did not activate, replacing it with another one was great. | rubertan eletronica silva joao monlevade |
| PHILCO | PH200N | Does not turn on - does not turn on standby | Diode d14 fr107 | Medium diode good but when it warmed up it started working again | Adriano de Souza |
| PHILCO | PH43U21DSGW | The TV displays the following symptom, the standby light turns on and turns on and the LED turns off and comes back on. It does not turn on by pressing it several times. The TV turns on normally. Doing the tests I found that the wifi wasn't working. | Capacitor c54 shorted to the 5v line on the board replaced, same problem solved, TV started working normally again | Adriano Miranda | |
| PHILCO | PB500BT | Panel works, but makes a buzzing noise and does not perform functions | Burnt 5 volt CD7805 regulator | Replace regulator 7805 | NilPassos |
| PHILCO | PH21SS | Power supply drive buzzing | Resistor r514 d 35 k changed | Moizaniel | |
| PHILCO | PH24T21DMTR LED | Does not turn on, 3v and 12v power supply | C106 com riple | Replace c 106 4.7nf 50v | POLYTEC |
| PHILCO | PH200 | Stuck on disk | U5 | After checking the entire component power circuit, the only solution was to replace the u5. | André Paixão |