Search:
Results: 87418

Repair Guide: Common Issues and Fixes

Brand Model Fault Detailed Problem Solution By
SONYBMC220
Af-8 connector miswired and ovf out of focus1) connector on af-8 board is wired backwards. 2) ovf is notin focus, even when lens and tape are in focus. -hq comments: 1) checked with nick mycanka, no other reports. pleaseresolder wires. 2) refer to service bulletin #160. adjust by eye forprope
SONYCDP101
Part numberT/n a00361r and s/b #191 all suggest modifications ofseveral c.d. models. new part numbers given for parts changed in thesemodifications do not match each other. in other words, a0036 and a0036rshow different numbers and s/b #191 shows numbers which ma
SONYD5A
Unit deadUnit goes dead, reset pin shorted (pin #8).
SONYSL2710
Part no. of chassisWe need a part number of chassis. -hq comments: please refer to s/b no. 195 (july 31, 1985). part numberis x-3681-108-7.
SONYKV25XBR
No raster/no sound but has high voltageUnit comes on with sleep time led and rgb ledraster, no sound but had h.v. found there was no +40v on d board.
SONYPSFL9
Incorrect set down mod.Need part # for modification. -hq comments: install edge-detection board (p/n x-4906-107-1).a diagram is available for installation.
SONYWMF65
Missing part numberRef. #222 pinch lever assembly. no part # in s/m or irp. -hq comments: p/n is x-3320-311-1. please refer to tape recorder s/b#176 nov. 1985.
SONYKX2501A
High pitch sound and shuts down, replaced ic1501After 5 days of playing (6 hours per day) unit would shutdown and high pitch sound would come from ga board. if set was turnedoff for a few minutes (2 min) set would operate ok for a few days.
SONYCDP302
No function or cannot read tocA small metal roller guide was sitting on top of the discmotor and preventing disc from setting on it. this roller came off fromdisc plate #373 which has 4 guides. -hq comments: the disc plate has been changed to a new one in currentproductions, and no
SONYKV1953R
No display - customer controls inoperative, q2004 and q2001Raster/hv ok, but local customer controls had no effect.channel up/down etc. inoperative. display dead. no waveforms at allaround ic2001 (controller).
SONYKV2675R
Pac-man pattern on screen, no videoNo vip function, pac-man pattern flashes on screen at theclock rate about once a second. rca uses this same ic051, mb88303, chipin some of their vcrs and they have the same problem.
SONYKV25XBR
Vertical jitterThis unit had a one inch vertical jitter when playing copyguarded tapes on a fischer vcr (model fvh 839).
SONYKV2691R
Muted picture and no vip operation and no remote, d-062The picture was muted and sometimes after warm up pix wouldcome on. ic052 pin 2 was high. found d062 installed backwards atfactory. d062 was installed cathode to b+. the board and the boardlayout show the diode anode to b+. the schematic shows catho
SONYSL10
Solenoid plungerThe original part # 1-454-349-41 was subbed to 1-454-365-51.the new solenoid fit the unit, but the collar on the plunger would notclear the mounting pieces on the unit. the original plunger had nocollar. we need to have the plunger changed on this sub.
SONYWMF15
Damage caused by batteryNegative end of battery heated up and pushed cabinet out. -hq comments: new batteries from eveready and duracell may have shortedinside the unit. they have a plastic skin instead of old metal. underthe skin is the positive cylinder, and negative termi
SONYKV2691R
Dark band across crt, replace q-204The unit had a dark band across the crt about 2/3 up from the bottom. the colors were also weak and somewhat out of phase.
SONYSLHF600
Distortion on beta hifiProblems with beta hifi playback and record. customer livesless than 1/2 mile away from a broadcast station transmitting on 1350kc.traced problem to the cable tv line that was hooked up to the fm input ontheir denon dra-400 receiver. the denon had a 75
SONYKV1972R
No manual control, replace ic105All front panel controls on the unit became inoperative (snd,pix, chan, pwr), however, the remote worked on all functions.
SONYKV2680R
No vip, replace ic-105No vip operation. all other functions worked correctly.
SONYKV1390R
Shutdown, replaced r559The unit would go into immediate shutdown. we shorted c535 todefeat the shutdown circuit and then ran the unit up on the variac. allother circuits were functioning properly.