PHILIPS TV Repair: Common Faults and Solutions.
Search: PHILIPS
Results: 14168
Results: 14168
PHILIPS Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| PHILIPS | 32PFL3403/78 | No sound, just a continuous knock knock knock on the speakers | Capacitors 2a04 and 2a08 of 220mf x 25v leaked, clean the board well and replace. | André | |
| PHILIPS | 32PHG4900/78 | Does not tune channels- no channels found | D101, specify varicap remover | Replaced the double diode d101e c132(1nf) and the TV works normally. | Albtron Eletronica - Tatuí,sp |
| PHILIPS | 32PHG4900 | I'm sound | Bios memory - u406; rewrite or change | Thiago MC Jaú | |
| PHILIPS | HTS3510/78 | Locked with the Philips logo on the display | Reset memory | Jump pin 3 of the XP15 connector to pin 13 of the XP9 connector, connect and then remove the jumper | Driu |
| PHILIPS | 40PFL5606D/78 | Duplicated and inverted image. | Rusty v-con and t-con flats. | Cleaning of flat contacts and image returned to normal. | TECNOBRU SBC |
| PHILIPS | FWM208 | Improve the serious | Put 10n cap in parallel with c539 and c540 | Warley cesar | |
| PHILIPS | FWM208 | Doesn't start | Smd cap 104nf parallel with the r bridge | Replace components. install the bridge outside the board with heatsink, heatsink on the q501, place 2 103 caps, one in parallel with r540 and the other with r543, making the woofer with bass and mid-bass. it turned out great. | Warley cesar |
| PHILIPS | FWM377 | Is only on standby | Loose drawer loading rubber. The device has to read the drawer sensors to release the on function | Ulisses Bernardes | |
| PHILIPS | 42PFL3604/78 | Doesn't turn on/sometimes turns on | Replace capacitors smd-c114/c80/c111/c417/c109/c113/c110/c474/c112/c155/c99/c168, note: some of them are inside the shielding plate of the microprocessor, after the change, wash the processor ci and the memory ci with brush and thinner | reginaldo moronte,eletronica junior caldas novas | |
| PHILIPS | 32PFL3018D | After changing the memory, the primary colors on the screen alternate. | Burn adjustment | With the TV on, type on the remote: menu, 1999, return. locate "burn in" and switch to off. | Persio (TVCompany) |
| PHILIPS | 47PFL3007D/ 78 | After being on for three hours, tsound is a strong hissing sound when we talk and it turns off and back on, sometimes the line on the screen | U701 regulator 3.3v altered p/4.27v | And just replace and run for the hug | JOSE HUMBERTO F SANTOS |
| PHILIPS | 48PFG6110/78 TPM 15.3L_LA | The tip is that the 55pfg5100/78 the scheme is the same as both the power supply and the main | Download the file from this site and good luck. | GDP2 | |
| PHILIPS | NX5 | Turning off right after turning on | DC current protection circuit at output | This circuit is simply not included in the schematic, but it is mainly composed of 2 transistors and 2 SMD resistors, what causes the problem are usually the 68k resistors, very close to one of the output inductors. | davi.sls |
| PHILIPS | 39PFL3008D/78 | Doesn't start | It only turned on the LED without an image, the back light flashed | Remove the memory, turn it on without the memory, then turn it off and solder the memory in place, it almost always works 100% | |
| TV PHILIPS | 42PFL6007 | TV doesn't turn on, just red light | Voltage did not double, change q603 q581.stk160 | luiz mario rocha | |
| PHILIPS | HTS3011 | It doesn't even turn on at +5v..12..2?...etc. | Raqqaa Saqaa | I went to the crowd | Alextecnico |
| PHILIPS | 32PFL4007 | Turns on, everything is normal, after a few seconds it turns off and restarts. turns on, Philips, turns off and stays like that the whole time. | Monitor the voltage on the 3.3v regulator u701. It has to be 3.3 volts. in my case tsound was 3.9v. | Replace u701, 3.3v regulator. | arock |
| PHILIPS | AZ1575 | Power button bad contact | Repair button | César zeppelini | |
| PHILIPS | 43PFG5000 | Turns on, "Philips" logo appears, turns off. The process is repeated all the time. | Try firmware update without success. The TV does not recognize a pen driver, with software for updating. continues: turn on, logo, turn off. | Resolved by changing the eprom memory | arock |
| PHILIPS | 40PFL3606D | Black lite black screen lights up | Resistor with open | Replace resistor 750k position 7503 | JORGETVPARANÁ |