PHILIPS TV Repair: Common Faults and Solutions.
Search: PHILIPS
Results: 14168
Results: 14168
PHILIPS Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
PHILIPS | 42PFL3508G/78 | Philips soon appears, sound remains, defective LED bars | Change panel LEDs | Luizsantos | |
PHILIPS | 47PFL4007G/78 | Takes time to exit standby | 3v3 regulator changed on the main board code: u701- reference: g1084-33 | Check its output, as in the test it is good | Ceará |
PHILIPS | 29PT4631/78R | Turns on and then turns off, the relay kept hitting (arming and disarming) | Transistors bc 7463 (bc327) and 7461 (bc 337) located near the power supply secondary capacitors | They were replaced and resolved, you can run for the hug! | ANTÔNIO ZWIRTES |
PHILIPS | 20PT120A/78R | When you plug it into the socket, the LED lights up when you click to turn it on, the LED blinks a few times but the TV doesn't turn on | The cause is the lack of 3.9 volt voltage coming out of the collector of the smd 7440 transistor or the smd 2442 capacitor | Changing the transistor and capacitor in my case | AssisTec |
PHILIPS | 32PFL3805D/78 | Not even the standby LED lights up, completely dead. capacitor c502 (100pf/1kv) burst. | Replace u501 (ncp1207) and resistors r514(10r), r515(10k) and c502(100pf/1kv) | Luir | |
PHILIPS | 40PFL6606D/78 | All dead stop | Change without testing q510 q501 and d101 and d102 | ELETRONICA PUBLISOM RGN | |
PHILIPS | 40PFL3606D | No image/characters, lamps on | Resistor 750 k na tcon aberto, perto ic 7j00 | oskarala | |
PHILIPS | 32PFL3404 | Red LED doesn't turn on | If you remove the connector from the power supply to the main PCI it works again | Replace c474 do 3v3 | Center som |
PHILIPS | 32PFL3404 | So led standby aceso | C474 perto do cristal x5 | DIVINO | |
PHILIPS | 14PT3331/78 | Input fuse blowing | Change fuse and ptc | eletronica sto ant rj bahia | |
PHILIPS | 21PT9467C/78 | Vertical closed from the middle up | D351=ba158 fully open | Replace it with another and run to another | Antonio Carlos (Eletrônica Renascer) |
PHILIPS | 21PT8467/78 | Vertical closed a line in the middle of the screen | In this case, the ak was the electrolytic cap, in position 2444 of 470/16v. It was only giving 400 microf. With the change, the vertical opened | Electrolytic cover, in position 2444 of 470/16v. It was only giving 400 microf. With the replace, the vertical opened | |
PHILIPS | 21PT8467/78 | Turns on, normal, but the sound appears little by little. taking time to get high. change the 2200/16 capacitor.. it may be good but it fails. The power supply comes from the chopper output and feeds the sound ci. | Turns on, normal, but the sound appears little by little. taking time to get high. change the 2200/16 capacitor.. it may be good but it fails. The power supply comes from the chopper output and feeds the sound ci. | Turns on, normal, but the sound appears little by little. taking time to get high. replace the 2200/16 capacitor.. it may be good but it fails. The power supply comes from the chopper output and feeds the sound ci. | Marcos-Confresa,MT |
PHILIPS | 55PUG6300 | TV does not turn on, power supply without any voltage at the output. | Diodo d9104(smd) em curto - diodo de 100v x 5a | Persio (TVCompany) | |
PHILIPS | 43PFG5000/78 | The LEDs turn on but tsound is no image | C109 c120 on the display ruler | Adeilton | |
PHILIPS | 42PFL3007D/78 | Flashing the philips name and it doesn't turn on | Power supply | Replace without testing the capacitor c9353 (330/16) and it's solved | Celio Paulo de oliveira |
PHILIPS | 20PT3331/78 | It didn't work with the remote control, it had 3v3 on the sensor | Change the sensor go and run to the hug | And | eletronica sto ant rj |
PHILIPS | 29PT529A/78R | No audio and making the audio applicator very hot. | Defective amplifier. swap c2883. | Paulo lopes | |
PHILIPS | 40PFG5000 | Turns on, dark screen back light on, no video. | See on the board "v-con" capacitor cp 20 shorted. | Replace cp20 | arock |
PHILIPS | 40PFL3605D/78 | 12v voltageless power supply only with 3.3v voltage | C502, q501, e u601 | I replaced the components listed and the power supply returned to normal | LUCAS EDUARDO |