Philco TV Repair: Common Faults and Solutions.
Search: Philco
Results: 4741
Results: 4741
Philco Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| PHILCO | PCS2952N | Burned fusil | D909 d911 eo c904 | And cool file | josé da eletronica schayonara em florip |
| PHILCO | PCM1443 | TV turning on the power supply and maintaining the 20v power supply | Causa dz904 | marcondes, OHM eletronica Jaicos-PI | |
| PHILCO | TP 2010 | TV doesn't turn on, stays on stand by | 8n2 capacitor 701 | Ohm eletronica | |
| PHILCO | TP1452N ? | Out of tune | C208, semi capacitance | Troar. | This email address is being protected from spambots. You need JavaScript enabled to view it. |
| PHILCO | TP1452N ? | Out of tune | C208 sem capacitance | Replace | This email address is being protected from spambots. You need JavaScript enabled to view it. |
| PHILCO | TP1452N ? | Out of tune | C 208 without capacitance | Replace it. | This email address is being protected from spambots. You need JavaScript enabled to view it. |
| PHILCO | TP20V56 55 02 F6949 06 2 | Vertical heating, with some scratches on the bottom of the screen | Cold solders, on the IC pins and smd capacitors that belong to the vertical. and at two solder points that go to pin 1 from the vertical to the r612a. | I did the general repair and it worked normally again. | eletronica melo boa viagem ,ceará |
| PHILCO | TP-2053 | Dark image then turns off and standby LED flashes | Cold solder on the terminals of the FC806a cable connected to the socket on the kinescope board | Resolder the f806a cable that is connected to the kinescope board | guaracy borges |
| PHILCO | PCR 2049 | Does not turn on, horizontal noise | C704 (471/2kv) | MB ELETRONICA | |
| PHILCO | PCS 2976 | Turns on and off with LED flashing until it burns out r917(2k2) | Cold welding d908 and d909 | Resolder and replace the resistor | ÁdrianChapadãodoCéu |
| PHILCO | TPF-2121 | Horizontal burnt q701 | Replace q701 (bu2506dx) e c715 (6n8/1k6v) | Marcio | |
| PHILCO | PCS 2976 | LED blinking very quickly | R917 open | 2k2 | ÁdrianChapadãodoCéu |
| PHILCO | PCM 2046 | Cesa screen with retrace line | C719 was stuffed | Just replace, send you the tips as well because they help | serginhosond@yahoo |
| PHILCO | TP2053 | Dead power supply | Ic 901 did not oscillate | betoteck | |
| PHILCO | TPF2940 | When the TV is turned on after a few minutes, the image darkens at once but the sound continues. Turning it off and turning it on again returns the image normally and after about 10 to 16 minutes it returns with the same defect. | I removed the capacitor c60 9 of 220nf x100v which was measuring about 202nf on the capacimeter. and the c606 of 47nonofaraides x250 vlts apparently good on the capacimeter, but it was bad | I replaced the two c606 and c609 close to the vertical output (note in some cases you have to replace up to the vertical output number; tda 8177f) it remained file | This email address is being protected from spambots. You need JavaScript enabled to view it. |
| PHILCO | 2956N | It went into protection, but when removing the connector from the horizontal deflector it worked normally, (with the horizontal closed of course). | Change wide capacitor (c728;3u3 1k6) tsound's no point in testing, change it, and run for the hug!!! | abreda | |
| PHILCO | 1444 | Turns on without characters on the screen, changes micro and nothing, tests resistors and diodes related to the problem and nothing. | Change ci tda-8361 | It was just a matter of changing it and it was fine. | Eronaldo(arteron) |
| PHILCO-HITACHI | PC-20R42 CH04 | Dull | Transistor q301 shorted and diode d305 leaking. | pardalzito | |
| PHILCO | PCM2046 | Vertical retrace | Elco c610 100 x 25v | johnny busnadiego | |
| PHILCO | PCM2046 | Does not turn on and voltages are ok | Elco c915 from the 20v power supply and can also be the d904 and zd904 | Capacitor replace c915 1000 x 35v | johnny busnadigo |