Philco TV Repair: Common Faults and Solutions.
Search: Philco
Results: 4741
Results: 4741
Philco Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| PHILCO | PT2054 | Burning horizontal outlet | C715 6n8/1k6v | Replace the same | Cezarel |
| PHILCO | TV 1453S | It takes a while to arm the power supply, sometimes it doesn't even arm. | R909 (390k) changed | Manoel | |
| PHILCO | PCM2146 | When it turns off after a few minutes, it is as if it goes into protection. | Str 50103 with leakage the power supply gave 90 volts and then dropped to zero giving the impression of being horizontal. | eletronica fernandes | |
| PHILCO | TP2054 | Does not tune channels and in normal av | Open smd resistor 303 | klein | |
| PHILCO | PT2054 | Poor tuning | Canal 03 paid no 27 and 05 paid no 30 | Replace the selector | paial.eletros |
| PHILCO | PCS 2952 | Blinking LED, +b normal power supply | Procedure: checking the horizontal circuit, I discovered the horizontal output transistor q703 (bu2508dx) shorted and the vertical output ci shorted (pin 6 shorted to pin 1), the +b of the power supply (120 volts) normally reached pin 1 of the flyback, 9 volts on the regulator ic701 (ba17809t), but tsound was no 24 volts on pin 6 of the vertical output IC nor the 12 volts on pin 10 of the flyback. | Researching the polarization circuits, I found the resistor r720 (0.47r 1/3w) open. I replaced it, the TV started working normally again. | andrefernandes44 |
| PHILCO | PVT1412/2012 DUETO | Power supply does not arm, you hear a tick, tick, tick.... | Capacitor c504 low capacitance | Replace c504 | NARDINHO-ALFENAS |
| PHILCO | PC-1452N | No image just drizzling | Defective mf201 | Replace | eletroclaudio aguas belas |
| PHILCO | PCM1444 | Stays on standby | R908 open | artemio | |
| PHILCO | PCM1446/2046/PCS2168 | Colorless image with stripes and hula hoop | Replace c205 -2,2/50 | JUVENAL PICOS-PI | |
| PHILCO | PCM 1446 | No sound with amplification on tda 8361 | Tda 8361 | I replaced it and just joy! | sinezio lbano |
| PHILCO | TP2054 | The stand by LED turns on, when trying to turn on the power supplys they are ok, but it does not oscillate and the LED keeps blinking | Fly back, when deactivating the micro protection, it oscillated and burned the abl line | Replace fly back, ov2094-d1 | bick |
| PHILCO | PC 1445 | No color | Resistor r118 (18k) aberto | Replace resistor r118 (18k) | rogerio santos |
| PHILCO | TPC2910 | The unfortunate one doesn't open the sides of the screen (belly on the sides) | Change q405, adjust ew | marcos hifi | |
| PHILCO | TPF2121C | TV with dark image, normal sound. | Check transistor bc 857- q 703. | sergiozap | |
| PHILCO | PCM-1444 | Flashing standby LED | Cold soldering on c706 | Resolder the c706 and check if tsound are more points to be resoldered on the same line. | Carlos Carbonari |
| PHILCO | PCS2976 | R919 20k amended | amsmariano | ||
| PHILCO | PCS 2952 | TV with the frame a little closed as soon as it turns on, as soon as it tunes a channel it folds horizontally and the tune goes out. | W. 720 47/25 from power supply +9 | Benê-Nepomuceno MG | |
| PHILCO | TP 2010 PCI016A | LED wouldn't turn on, blinking with a small power supply crackle | Resoldar c-921 smd e x 301 | eletroléo | |
| PHILCO | TP 20V56 | Sem audio no av | Replace i.c 490 | Replace i.c 490 | This email address is being protected from spambots. You need JavaScript enabled to view it. |