Philco TV Repair: Common Faults and Solutions.

Search: Philco
Results: 4740

Philco Repair Guide: Common Issues and Fixes

Brand	Model	Fault	Detailed Problem	Solution	By
PHILCO	TP2920	When it turns on, the LED goes off, the tube blinks a few times and goes off, then the LED keeps blinking	Changing capacitors c1701 and c 1703 6n8x1k6v polyester.......it was zero again!!!!		adilson
PHILCO	PH14C	Dark image	BF 422 and 423 leaking, change all BF's on the TRC board		Continental
PHILCO	PCM 1444.2044	No color.	Swap.c.504.	Resolved	hermildon jose t de sousa
PHILCO	TP14U56	When plugged into the socket, the power supply gave a signal that it would work but it didn't, and the LED didn't even light up. and the +b voltage was just 10v and the normal 4.7v voltage	R107 of the LED and e-prom system was open and the sw101 was broken.	I replaced the touch switch on the power sw101 and it turned on but the LED didn't work, I replaced the 100k or107 and the LED came on then it was just a hug.	DIGITEC ELETRONICA (65)9608-4535
PHILCO	PC-1438	Does not turn off via remote control	Q-902	Replace and test.	ELETRONICA NISSEI SOUND embu-sp
PHILCO	TP2053S	TV didn't light anything; power supply did not oscillate, secondary zero	In my case it was the open resistor r911 2,200k		chinês eletronica solânea
PHILCO	PCM-1451	It doesn't turn on via the remote control, but via the panel and then the remote with all normal functions	Believe defect in the main power supply	Replace of capacitors c913 and c911 of 1μF/100v and 100μF/25v respectively.	eletrônica fernandes(to)
PHILCO	TP29C21	When the TV is plugged in, it activates normal stand by, but when you press the power key, the LED goes off as if it were going to work and nothing, only the LED keeps blinking	Lack of -12v voltage on the power supply secondary	D 909a shorted, r 912 and r 910 open. When replacing the TV it worked normally.	Eletronica Som & Imagem
PHILCO	TV PH21SS TV PH21SS	Nâo liga nem led stand by	R520=120k	In my case it was (r520=120k) - it worked 100%	neupsx4
PHILCO	PH 21C	Does not turn on, device inoperative +b only 30v and does not oscillate	3v3 supply failure, diode d872 shorted causing the defect.	Replace 3v9 diode d872	celinvds
PHILCO	TP1454	When a vertical line appears on the screen, when viewing the video, the screen opens and closes with retrace lines	C730 - capacitor de largura horizontal 6n5 x 1,6kv		Domingos da Eletronica
PHILCO	PCM1446 PCM1446	Fire broke out on the flyback	Holey flyback	I replaced the flybek and it worked right away. this tip is great	kynnka
PHILCO	PH 21C	Low power supply +-80v partially closed frame	Place 1 22k resistor in series with the power supply reference resistor		warley cesar
PHILCO	TP2054	Does not work.	Fuzivel quimado	Blown fuse due to shorted c-909	RAIMUNDO
PHILCO	TP2053	Power supply does not oxidize	There was no 11 volts on pin 14 of the ci 901's vcc and there should have been 11v on pin 2 of the ci 901 in staby, c 917 and c 907 smd with leak		BRUSKE
PHILCO	TP2054	Power supply does not oxidize	There was no 11 volts on pin 14 of the ci 901's vcc and there should have been 11v on pin 2 of the ci 901 in staby, c 917 and c 907 smd with leak		BRUSKE
PHILCO	PH14D	Completely inoperative power supply stopped	Q801		carlinhos100
PHILCO	PCS2976	Cut-off tube	After changing the tube, flyback, and vertical output it worked without sound	Replace eeprom	ÁdrianChapadãodoCéu
PHILCO	PCS2952	Dull, bright when turned off	Screen voltage was very low even when measuring directly on the wire, with it disconnected from the board	Changing the tube socket, which, if it leaked, killed the focus voltage and the screen on the fly	jasvan souza
PHILCO	PC1442	White tla with retrace	Zd 304	Replacement	This email address is being protected from spambots. You need JavaScript enabled to view it.