Philco TV Repair: Common Faults and Solutions.
Search: Philco
Results: 4740
Results: 4740
Philco Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| PHILCO | TPF 2121 | Morta (nem da stand by) | D908 e c914 | Obs: mude c914 p/ 1000y/35v | VSE Eletrônica(Ádrian) |
| PHILCO | TP2054 | Does not turn on, LED is off. | R 911 amended. | Replace. | This email address is being protected from spambots. You need JavaScript enabled to view it. |
| PHILCO | PCM2044 | Lack of sync and drizzle | C205 - agc and c702 sync. I changed the caps. It started working normally again. This email address is being protected from spambots. You need JavaScript enabled to view it. | The two electro/capacitors with high esr. | vxm |
| PHILCO | TP1452N | Does not turn on, stays on standby | When the TV is on stand by with the LED on, replace the zd923 4.7 volt diode and the zd922 3.9 volt diode. | Edilson Ribeiro | |
| PHILCO | TPF 2941 | Does not turn on or the LED lights up | All voltages are normal, and the TV does not turn on; fed up with stress, I decided to change [x1] that little crystal that is next to every micro, in this case x1 = 20,250, I changed it, I confirmed, it was the one, [if] it happens, here's the tip | fabinho@3a | |
| PHILCO | PCR1449 CPH06M | C912 with leak, change, note there is no general voltage in the secondary | ars | ||
| PHILCO | PCM-2044 | When the TV was turned on, it worked with a lot of flickering on the screen and it was difficult to maintain the tuning of a channel and when changing channels it got even worse, it shook the whole screen and was like a simonism of vertical and horizontal | The capacitor c710 with cold soldering, I resoldered it and it was file | It is located next to the dryve of the horizontal | This email address is being protected from spambots. You need JavaScript enabled to view it. |
| TV PHILCO | TP 29C21 | TV doesn't work, STD-BY light stays on | Solution replaced the d-916 smd | jaironuness | |
| PHILCO | PCM 2044 | When turning on the image comes back to normal after a while the screen becomes clear until the image disappears | Replace ci tda 8361 s7 | This email address is being protected from spambots. You need JavaScript enabled to view it. | |
| PHILCO | PCM 2044 | No image. No sound, no OSD, screen flashing on the power pin, the voltage fluctuates on and off, disconnect pin 35 on the micro controller and the TV stops turning off. So here the screen is white as if the screen was at maximum but without a delay line | Tube exhausted zerrrrrrrrrrado | This email address is being protected from spambots. You need JavaScript enabled to view it. | |
| PHILCO | PCS-2952 | Arming protection | C727/470p+r718-10k+dz712/8,2 | JACKSSOM | |
| PHILCO | TP-2052 | Does not turn on, turns on standby | Res. 942 12k | vicena | |
| PHILCO | TP2054 *** | The TV turned on when I wanted, it worked for about 5 minutes and turned off, I noticed that the LED was lit dimly, you started it, it just blinked, I checked +b it was oscillating when I measured the voltage on the fet, normal voltage, I changed the IC 901, nothing changed, I released pin 3 of the IC 902 photo coupler the voltage at +b was normal and the TV worked normally, but it presented another defect with a black stripe on top. I replaced the c-715 6n8/1kv with 8n7/1kv and the strip normalized the image was good, but the sides dir / left making curves and ghost image I checked c-911 and everything was resolved. | Replace c-715 c-911 | C-715 de 6n8/1kv por 8n7/1kv c-911 470x25v. | wagner |
| PHILCO | PC2039. | No audio/normal image. | Capacitor c-513=10nf was detected, defective. | The same was replaced and only joy. | Armando da Eletrônica só Tv. |
| PHILCO | PC2043 | Does not come out of standby. | R-908=82k was found open. | It was replaced and it was... ok. | Armando da Eletrônica só Tv. |
| PHILCO | TPF 2941 | Turns off after a few seconds | C-805 without capacity | To replace | Alvaro Prolar |
| PHILCO | TP2052 | Volume in 3 levels - (mute/medium/maximum) | Altered memory | Initialize the manual conf memo. (turn on the socket, while holding down the channel+/- keys for 15s) | MAIRES |
| PHILCO | PCM2046 | Warping.h.in some channels | C.722 470.mf.25v | julio itaguai | |
| PHILCO | PCM 2048 *** | When I turned on the TV, the pacifier made noise as it was leaking voltage, and the TV would have no image, a blue screen and running out of frequency, I cleaned the pacifier and put it back but it didn't solve it, then the noise went to the cannon, but not anymore. it was the cannon, opening the shock notice that the screen cable had dry solder. I redid the solder and the TV was normal | Write cable with dry solder if you don't decide to change the shock. | Rusty shock. | wagner |
| PHILCO HITACHI | PC1441 | Does not turn on, secondary dead, primary with normal voltage but the power supply capacitor does not discharge, with the multimeter tip on the capacitor's ground and another on pin 3 of the str the TV turns on | Open resistor in the 82k power supply r 902 or faulty | geovani da silva |