Philco TV Repair: Common Faults and Solutions.
Search: Philco
Results: 4740
Results: 4740
Philco Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
PHILCO | PCS-2956 | Horizontal change, turns on works normally and suddenly burns out again. | Swap c7283n3/1k6 was c 2n2 | I replaced it and plz | Eronaldo |
PHILCO | PCM-2051 CP01R0 | It doesn't come out of stand-by by pressing power on the CR or CH+ TV. The LED wouldn't turn on, blinking. | Normal power supply voltages high 110v and also low (in stand-by) | Replace deflector coil | TODDY |
PHILCO | PCS 2976 | High power supply 130 v giving 150 v if turning off | R 919 120 k amended | jps elet cg | |
PHILCO/ GRADIENTE | TP 2921 | Turns off after +or- 10min and stays on std by | Ic 501 tea1507p overheating | Replace the same | livo tecnovideo ps |
PHILCO | TP 2052N | Power supply pulsing, LED blinking, slow to turn on | C 913 | ||
PHILCO | TP 2052N | Does not tune channels or poor tuning | Cristal mf 201 | Manoel | |
PHILCO | PC 20R38 | Screen with retrace, no brightness or contrast | C301 0.47yf/35v close to ci oscillator | AdrianChapadão | |
PHILCO | PCM-2051 | LED blinking and power supply oscillating | Capacitor c913 1uf | pardalzito | |
TV PHILCO 29 | TPF-2902 E OUTRAS TVS | No image (brightness), normal sound, with high voltage, trc filament lights up and normal voltages on the rgb. | Oxidized tube connector, remove and replace the tube plate and it's shiny! | Clean the TRC terminals, spray with WD40, remove the TRC plate several times or if it doesn't look good, replace the connector! | Dreamshacker |
PHILCO | TPF 2130 | It turns on but when the relay goes off it turns off and stays on standby flashing | Replace o ic 601 (stv 9302a | allanaeletronico | |
PHILCO | PC-2035 CPH-03 | Horizontal synchronism | C 613 with leak | To replace | Alvaro |
PHILCO | TP 2921 GRS | Power supply +b 130 +b 10 +b36 only the +b 6.5v does not work | Micronas vtc 4942 | Replace micronas along with the eeprom obs. Heat the 35 watt soldering iron and unplug it to carry out the welding ok | luiztvsom |
PHILCO | TP 2021 GRS | 130v power supply at 0 volts | 330 k resistor r 509 open | Replace r 509 smd I replaced it and it worked fine | luiztvsom |
PHILCO | TP1454 **** | The LED turns on and when you turn on the TV it turns off. | Does not start | Was replaced r-715 =3k3 was cut. | Armando |
PHILCO | PCM 1443 EMOTION | Everything works normally, but if you turn it off and turn it on at the same time, it no longer turns on and the +b stays normal. | R 908 open | Daniel | |
PHILCO | TP 2054 .... | Tv doesn't work | Short circuit | Disk capacitor position = c959 shorted | Armando |
TV PHILCO | PCS 2976 | Horizontal dark stripe | C 705 with amended | I replaced it with another one I thought it could be service mode | kizeuu |
PHILCO | 2054 | Power supply inoperative fuse ok | R909 390k | Roberto Consertos | |
PHILCO | 2976 | TV stays on stand by and when you press power the LED turns off and then lights up again | Replace fly back | Roberto Consertos | |
PHILCO | 2976 | TV works normally but with a horizontal bar on the left side | Replace capacitor smd c705 no pino 16 do micro | Roberto Consertos |