Philco TV Repair: Common Faults and Solutions.
Search: Philco
Results: 4740
Results: 4740
Philco Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
PHILCO | PH32S61DG | No image, dark screen, backlight off | Vd752 = sb2200 | Vd752 = sb2200, an sb3200 diode was placed in place, it is close to the LED connector. | silnei |
PHILCO | PH32D | Plugs it into the socket, the green LED lights up, changes to red and does not turn on | C14 = 47mf x 35v on the defective power supply board | Replace capacitor | silnei |
PHILCO | TP 2052 | No image, when you adjust skreem the image appears | Place a filter capacitor parallel to the existing 22mf x 250v | AGILDO ANDRADE | |
PHILCO | PH40R86DSG | Burning the LEDs | Power supply that feeds the LED buses with 67.5v. | 1st replace the LEDs. 2nd lower the LED voltage from 67.5 to 60v. remove all resistors rw812, 805, 811, 825 (smd r300=3r) insert a 6r resistor the voltage will drop to 60.5v | EvandoViana |
PHILCO | PH42M | TV turns off the image after 20 minutes. | Transistor a19t - ao3401 - leaky (heating too much and turning off the 12v supply to the t-con. | Replace said transistor. | JHtron |
PHILCO | PH21MSS | Burning the r816a | Transistor q802(5551) shorted | Replace for the same | Eletrônica Bastos |
PHILCO | PH39N91D | The league comes soon and then fills with stripes, the image disappears and is left with sound | Change the smd cap on the v com board and go for the hug | eletronica publisom egn | |
PHILCO | PH39N91D | The league comes soon and then fills with stripes, disappearing the image, leaving only sound | Change the smd cap on the v com board and go for the hug | eletronica publisom egn | |
PHILCO | PH21MSS | It doesn't turn on, the LED just keeps flashing | Diode | ||
PHILCO | PH32UDSGW | LED bars do not light up, voltage is only 38 volts and does not rise to 65 volts to light them | Faulty dp403 diode | Even though it was ok, I replaced this diode and the LEDs came back on correctly. | ser-mga |
PHILCO | PH43N91 | Doesn't start. the standby LED doesn't even light up | Missing 12v and 24v voltages, resistors (rw938,967, 952, 969, 970, 971, 972, 973) all blown | Replace the resistors, everything solved | CDS_DIAS |
PHILCO LED | PH28S86DG | Does not turn on standby | Defect in the power supply two caps. electr. 330/35 | Replace with 2 cap.470/50 sono show | RNeletronica |
PHILCO | TP14U56 | This TV arrived on standby and won't start | After thorough research I found the 915 diode ref; 1n4531 I used the 1n4148 the TV worked normally | Just run for a hug, good luck! | CLIC |
PHILCO | PH21MSS | Power supply with 20v | Rewrite the memory | Rewrite the memory.. | Daniel. .Mauriti CE |
PHILCO | TPF2130 | Turn on and off | When it disconnects horizontally from the deflector, it no longer turns off. | Changing the horizontal capacitors (2 blue capacitors) | Josimar |
PHILCO | PH40D10DSGW | Normal stand by power supply lit, when turned on the 12v power supply drops and does not turn on | Dp401 diode shorted | Just replace it and solve it | Luiz videotek |
PHILCO | PH200N | It doesn't turn on, just the blue light stays on. | Corrupted u3 | Replace u3 or re-record | Vander CDs de Quixadá CE |
PHILCO | PH21B | League oscillates without image screen off | C 450 next fly back 681k 2 kv replace | Replace and run to the crowd | Laercio Gonçalves umuaramapr |
PHILCO | PH39F33DG | Sometimes the backlight turns on and then turns off, giving the impression that it is the LEDs, the image remains blinking | Defect on the power supply board, power supply with less than 390v drops to 250v | Remove the 307,308,309e310 smd registers, clean the glue and run to the hug | Luiz videotek |
PHILCO | PH58E51D | Doesn't start | Power supply has no voltages | Replace the 10k r115 which is open and the ci u1 tea 1755t which is short circuited. | Danubio |