Philco TV Repair: Common Faults and Solutions.
Search: Philco
Results: 4740
Results: 4740
Philco Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
PHILCO | PH32N62DG | The black light doesn't turn on | Glue under the smd r95 resistor | Take out the resistor, clean the glue from below and on the resistor board again. | Rafael |
PHILCO | PH40E36DSGW | Turning off less than 10 minutes | C111 | Remove and only joy | Marcos roberto |
PHILCO | PH40D10DSGW | Does not turn on, completely stopped, without voltages on the power supply secondary. | Up201 causing short in zdp201 cp202. | Changing the up201, checking all nearby components. | Antony Garcez |
PHILCO | PH21MSS | The screen full of line, vertical defect | Replace resistor r306, 220r | DJ PITUKA | |
PHILCO | PH40U16DSG | Sometimes it turns on, sometimes it doesn't, when it turns on the power LED turns off and returns to the stand bay again, sometimes it even shows the Philco logo and turns off | Change cp from the primary power supply, cp 105 cp 201 and cp 205 and run for the hug | Eletrônica Power saquaçú RJ | |
PHILCO | PH32U20DSGW | Burning leds | Change all the LEDs and remove rp411 rp433 from the circuit to reduce the voltage from 62 volts to 54 volts | Replace all the LEDs and remove rp411 rp433 from the circuit to reduce the voltage from 62 volts to 54 volts | antonio nobrega (patos pb) |
PHILCO | PH32B51DSGW | The Philco logo appears then turns off and restarts | Update | Download from the Philco website which has the instructions. | Mariano |
PHILCO | PH21B | +b of 110v = 61 to 80, without -14 and +14, it kept making a noise in the tragus or ci oscillating, cutting the secondary voltages | R 553 from 5.6k changed to 7.8k | Just replace | Marcleo |
PHILCO | PH39F33 | Red LED on but not turning on | I even replaced the ic u201 but it was not the cause of the problem. | On the power supply board, disconnect plug p1 (it is next to l201) and then connect the power socket. then unplug the socket and reconnect plug p1. | littlecarlos |
PHILCO | PCS2976S | With vertical colored stripes | Obs r709 of 18r altered with low value causes this defect | Changing resistor can put 22r | jose joaquim |
PHILCO | 32E53SG MS63LA MAC2HG | TV arrived sound with faulty electronics, turns on the Philco logo and turns off, just tighten the screws on the power supply and run for the hug | Tighten the power supply screws | Raimundo | |
PHILCO | PH21C | When connecting the TV to the socket, the stand bay ledy turns on the power supply, the TV tries to assist by making a strange noise in the image tube, like frying and it does not generate high voltage. | Change the picture tube and the TV will work normally. God be praised! | Sinailson furtado | |
PHILCO | PH21M SS | Does not turn on, LED is on, and turns off but does not turn on, high supply with 159v | Change resistor r810, 15k next to the photocoupler. | DJ PITUKA | |
PHILCO | TPF2121C | Turns on and off with a black screen, difficulty turning on. | Change booster capacitor c715 .68, next to the horizontal transistor. | DJ PITUKA | |
PHILCO | TP2920 | Colored line at the top of the screen | Replace the two 6n8/2kv polyester capacitors | José | |
PHILCO | PH32M A3 | The stand bay LED does not turn on, flashing intermittently, with a voltage of 5v and 12v on the missing power supply. | B1,aa,qa | Replace the photo coupled to the tl431 and the q33 which is the d478 mosfet and the TV will be working normally. God be praised! | Sinailson furtado |
PHILCO | PH43C21P | It doesn't work, just the standby LED blinks. noise at the power supply. | Changing two 1000/10 capacitors in the cx820 and 821 power supply. | Danubio | |
PHILCO | TP-2054 | Doesn't start | Fly-back | Replace fly-back ov2094d1 replacement jf0501-19192a | Sinailson furtado |
PHILCO | PH32F33DG | Standby LED flashes continuously and does not turn on | Software defect on the main board and flash memory | Download software from the philco website, format pendrive, insert the 2 files on the pendrive, unplug the TV, insert the pendrive into the TV's USB, turn on the TV with the power button pressed until the software installation menu appears, the TV will reboot, then that's it. run to the hug | OSVALDO SEABRA |
PHILCO | PH22B16D LED | Scans/squares/freezes on digital channels | I tried the tuner and it didn't solve the problem, but the defect was in the tuner's 3.3v supply. | Replace u001 3.3v regulator with 2.8v.... | MIGUELTV |