Philco TV Repair: Common Faults and Solutions.
Search: Philco
Results: 4740
Results: 4740
Philco Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
PHILCO | PH21MSS | After switching on, a normal image appears. It turns off in seconds and the LED keeps flashing indefinitely, even if you remove the plug it still flashes several times. | Q 802a with leak. it is close to the deflector coil fitting. | Replace | Ferraz |
PHILCO | PH21E | Turns on with vertical partially closed after 5 minutes turns off | Check r839 r881a and c883 both changed | Replace the 3 | Reinaldo Cáceres |
PHILCO | PH650 | Stand by LED is on but the device does not turn on | Smd transistor q13 2n3904 on the main board of the amp responsible for power control leaks, replace without testing | A bc548 was placed in place and the device worked perfectly | ELISEU |
PHILCO | PH21SS | Screen with 3 fingers on the sides | R553 5k6 changed | And just replace and go for the hug | Robsom |
PHILCO | PH 21MSS | It doesn't turn on, it stays in stand bay | Fly-back | Replace the bsc250230z fly-back if you don't have this fly-back, replace it with the bsc25-n1579, just run for it. God be praised! | Sinailson furtado |
PHILCO | PH32B | Red LED doesn't turn on | 12v and 24v when turned on the voltage drops | Electrolytic ec4 33x25v | Center som |
PHILCO | PB 126L | Nao and usb | Measuring 5v from usb was not available. I changed the USB touch key and it worked.. | Just replace the USB touch key and the same as the Pley | Eduardo Callai |
PHILCO | PH21B PH08K-A(VER:0.7) | Vertical closed shutting down | Lack of 8 volts on pin 3 of icn301 causes capacitor c312 to short, replace and it worked | Luis Aquino sparapan | |
PHILCO | PH24D20DG LED | TV turns on works perfectly after a few minutes disappears the image remains with the becklit on and with audio | Screen defect | Dp4 diode on the screen board with leakage, just replace it and run for the hug!!! | JORGE ASSISTÊNCIA TÉCNICA COTIA SP |
PHILCO | TP1452N | No audio. | Broken track, in line with the 9v regulator, close to the vertical output | MARCONES DE ARARIPINA PE. | |
PHILCO | TP1452N | Vertical closed at the bottom, and asking for a password on most channels. | Defective varicap selector | Resolved by changing the varicap selector. | MARCONES DE ARARIPINA PE. |
PHILCO | PH32F33DG | Shutdown after about 3 to 4 minutes... | Faulty LEDs. | Check the voltage consumed by each LED bar and replace damaged LEDs. | |
PHILCO | PH58E38DSG | After repairing the LED bars, insert a 3030 LED, go to the inverter that powers the bars, remove each 5r6 resistor from the supply of each fet and put 10r in its place, tsound are 5 fets | This solution will reduce about 4 volts from the bars, prolonging their life, abs | jobovi | |
PHILCO | PH58E38DSG | Turns it on, comes logo and locks everything, erasing | With a 350v power supply, (mounted for this purpose) test each LED bar, they all have to have the same ddp, if any bar shows a much smaller drop, it has a burnt out LED, a short | jobovi | |
PHILCO | TP2054 TP1400 | Philco TV does not light up the LED or have any voltage on the secondary power supply | R 911 open it stays in the primary power supply | It was just a matter of changing the resistance r 911, it is in the primary power supply | Jil da Eletrônica |
PHILCO | PH21UA | Doesn't start | N504(coupler photo) | To replace | Rojo |
PHILCO | PH21MSS | Power supply | Burning ci ncp1337p from power supply | Replace main capacitor in the power supply primary 220 × 400 | batista |
PHILCO | TPH21M SS | When connecting the TV to the socket, the stand bay ledy turns on by pressing the channel button + the stand bay ledy turns off but the TV does not generate high voltage and makes a hissing sound at the power supply. When removing the Q802 from the board, the TV turns on, generating high voltage and the image is normal but with black side bars and the vertical folded at the top of the screen and tsound is also no sound! | C851 | Replace the c851 with a 10k short and the TV will be working normally. God be praised! | Sinailson furtado |
PHILCO | PH21SS 21C1PH02-2H | Won't turn on ONLY LED stand by on power supply +b 60 volts | R 553 with open glue 5k6. | Lidio Elsique Da Silva | |
PHILCO | PH21M2 | Stained, colored screen | Bloated capacitors and stv8172 vertical output | Replace for another equivalent output | bonfim |