Philco TV Repair: Common Faults and Solutions.

Search: Philco
Results: 4740

Philco Repair Guide: Common Issues and Fixes

Brand	Model	Fault	Detailed Problem	Solution	By
PHILCO	PH39U21DSGW	After pressing the power button, the TV turns off in a few seconds. +or - 40 sec	Corrupted memory	Update memory	Bili
PHILCO	PH40E36DSGW	Turning off in less than 10 minutes. You have to wait a few minutes to be able to turn it back on again. however, it starts to turn off more and more quickly.	Removed capacitor c111 smd. It is between the processor and the flat. close to q8 and d5. which connects the 5v standby line. (tip from Robert, right sound on the website. However, the location of the capacitor was defective. I'm replacing the tip to make it easier to find it.)	I replaced it and it resolved.	Eletrônica R-Tec
PHILCO	PH40R86DSGW	No image, only sound	In this case, tsound is no point in changing any burned-out LEDs, you have to change all the LED bars, because even when they are turned on, all the LEDs are changed and go out.	After the replace resolved	PATRICK ELETRONICA
PHILCO	TP2054	With sound and menu without image	R723 (4k7) smd na linha do abl	I replaced it and it went back to normal	Emanuel (Alfa Eletronica)
PHILCO	PH21B	Turning off with noise from the speaker	V502
PHILCO	PH48S61DGH	LEDs came on and then went out	I removed the 5.6k 766 resistor. and everything was fine		Adalton ms vigia
PHILCO	TP-2053S	Does not turn on standby, keeps blinking	Era o flyback	Flyback short switch	Gilson Paulistana
PHILCO	PH39E53SG	Flickering image	On the screen ruler, remove r851 and jam it, it is next to c812 and also next to u801		badri eletronica <small>This email address is being protected from spambots. You need JavaScript enabled to view it.</small>
PHILCO	PH24M-LCD	TV locked showing padlock, some remote control keys don't work	Eprom 24q16b	24q16b eprom replacement	EDSON
PHILCO	PH39R25DSG	Burned inverter mosfet TF450 in short (aotf450) difficult to find and very expensive.	I put a 7n65, it worked but got a little hot. LEDs lit up normally.	I replaced it with a 13n50 and it went back to normal. LED output voltage is +/- 140v.	Mau3000
PHILCO	TFP2130	TV turns on normally with a beautiful image, but the image has a flash or lightning in the image and very thin colored lines	C=607 shorten	Replace it with another and run to the hug	Antonio Carlos (Eletrônica Renascer)
PHILCO	PH42M61	Call and "wait", sometimes it works, sometimes it doesn't. does not tune channels. sends hdmi inputs, for example, tv turns off. doing wrong functions.	Change the ci that generates a voltage of 3.3 v, close to the channel selector.	Replace 1117-33	arock
PHILCO	PH21MSS	It doesn't turn on, the standby LED comes on, I turn it on on the control, the LED goes off and doesn't turn on, the power supply goes to 60v and drops to 20v. and the LED is blinking	Change c847, c827, q802 and r845 as a jumper		DJ PITUKA
PHILCO	PH21SS	Does not tune the channel, with all voltages on the varicap	Replace r317 ,47k e r318 ,12k do lado do varicap.		DJ PITUKA
RADIO PHILCO	PH229N-USB	Fm doesn't pick up correctly	Diode diode d300 and 3001 shorted		julinho da eletronica
PHILCO	PH28D27	Every stop, no LED lights up	U905 burns due to a power outage, sometimes it burns, other times it doesn't burn and makes everything stop and just change it and go to the hug, it stays close to the coil l818 eup3		eletronica publisom de natal
PHILCO	PH28D27	Every stop, no LED lights up	Change all the capacitors in the power supply and go to the hug		eletronica publisom de natal
SEMP TOSHIBA PHILCO	48L2400 PH48	No image white screen LED on	Cd17	Shorted smd capacitor on t con plate	Adrian Chapadão do Céu Goiás
PHILCO	PH42F10DSGWACVA	Restarting without stopping	Short in keyboard line	Smd capacitor position ck2, next to the processor, shorted	shermanflima
PHILCO	PH21MSS	Turns on, image appears and turns off and the LED blinks	Replace resistor r816a 390r, r818 820r, cap c833, c835, c847, c826, q802 coloquei mpsa42		DJ PITUKA